 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Features * * * * * * * * * * * * 80C51 Core Architecture 256 Bytes of On-chip RAM 256 Bytes of On-chip XRAM 16K Bytes of On-chip Flash Memory - Data Retention: 10 Years at 85C - Erase/Write Cycle: 100K 2K Bytes of On-chip Flash for Bootloader 2K Bytes of On-chip EEPROM - Erase/Write Cycle: 100K 14-sources 4-level Interrupts Three 16-bit Timers/Counters Full Duplex UART Compatible 80C51 Maximum Crystal Frequency 40 MHz. In X2 Mode, 20 MHz (CPU Core, 40 MHz) Three or Four Ports: 16 or 20 Digital I/O Lines Two-channel 16-bit PCA - PWM (8-bit) - High-speed Output - Timer and Edge Capture Double Data Pointer 21-bit Watchdog Timer (7 Programmable bits) A 10-bit Resolution Analog-to-Digital Converter (ADC) with 8 Multiplexed Inputs Power-saving Modes - Idle Mode - Power-down Mode Power Supply: 3 Volts to 5.5 Volts Temperature Range: Industrial (-40 to +85C) Packages: SOIC28, SOIC24, PLCC28, VQFP32 * * * * * * * Low Pin Count 8-bit Microcontroller with A/D Converter and 16 KBytes Flash Memory T89C5115 AT89C5115 Rev. 4128F-8051-05/06 Description The T89C5115 is a high performance Flash version of the 80C51 single chip 8-bit microcontrollers. It contains a 16-KB Flash memory block for program and data. The 16-KB Flash memory can be programmed either in parallel mode or in serial mode with the ISP capability or with software. The programming voltage is internally generated from the standard VCC pin. The T89C5115 retains all features of the 80C52 with 256 bytes of internal RAM, a 7source 4-level interrupt controller and three timer/counters. In addition, the T89C5115 has a 10-bit A/D converter, a 2-KB Boot Flash memory, 2-KB EEPROM for data, a Programmable Counter Array, an XRAM of 256 bytes, a Hardware WatchDog Timer and a more versatile serial channel that facilitates multiprocessor communication (EUART). The fully static design of the T89C5115 reduces system power consumption by bringing the clock frequency down to any value, even DC, without loss of data. The T89C5115 has two software-selectable modes of reduced activity and an 8 bit clock prescaler for further reduction in power consumption. In the idle mode the CPU is frozen while the peripherals and the interrupt system are still operating. In the power-down mode the RAM is saved and all other functions are inoperative. The added features of the T89C5115 make it more powerful for applications that need A/D conversion, pulse width modulation, high speed I/O and counting capabilities such as industrial control, consumer goods, alarms, motor control, etc. While remaining fully compatible with the 80C52 it offers a superset of this standard microcontroller. In X2 mode a maximum external clock rate of 20 MHz reaches a 300 ns cycle time. Block Diagram T2EX RxD TxD Vcc Vss PCA ECI T2 10-bit ADC VAVCC VAGND VAREF UART RAM 256x8 Flash Boot EE 16K x loader PROM 8 2K x 8 2K x 8 XRAM 256 x 8 PCA Timer 2 XTAL1 XTAL2 CPU C51 CORE IB-bus Timer 0 Timer 1 INT Ctrl Parallel I/O Ports Port 1 Port 2 Port 3 Port 4 Watch Dog RESET T0 T1 INT0 INT1 P1(1) P2(2) P3 Note: 1. 8 analog Inputs/8 Digital I/O. 2. 2-bit I/O Port. 2 AT89C5115 4128F-8051-05/06 P4(2) AT89C5115 Pin Configurations VAREF VAGND VAVCC P4.1 P4.0 P2.1 P3.7 P3.6 P3.5/T1 P3.4/T0 P3.3/INT1 P3.2/INT0 P3.1/TxD P3.0/RxD 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 P1.0/AN0/T2 27 P1.1/AN1/T2EX 26 P1.2/AN2/ECI 25 P1.3/AN3/CEX0 24 P1.4/AN4/CEX1 23 P1.5/AN5 22 P1.6/AN6 21 P1.7/AN7 20 P2.0 19 18 17 16 15 RESET VSS VCC XTAL1 XTAL2 SO28 VAREF VAGND VAVCC P4.1 P4.0 P3.5/T1 P3.4/T0 P3.3/INT1 P3.2/INT0 P3.1/TxD P3.0/RxD XTAL2 1 2 3 4 5 6 7 8 9 10 11 12 SO24 24 P1.0/AN0/T2 23 P1.1/AN1/T2EX 22 P1.2/AN2/ECI 21 P1.3/AN3/CEX0 20 P1.4/AN4/CEX1 19 P1.5/AN5 18 P1.6/AN6 17 P1.7/AN7 16 RESET 15 14 13 VSS VCC XTAL1 4 3 2 1 28 27 26 VAVCC VAGND VAREF P1.0/AN 0/T2 P1.1/AN1/T2EX P1.2/AN2/ECI P4.1 P4.0 P2.1 P3.7 P3.6 P3.5/T1 P3.4/T0 P3.3/INT1 5 6 7 8 9 10 11 PLCC-28 25 24 23 22 21 20 19 P1.3/AN3/CEX0 P1.4/AN4/CEX1 P1.5/AN5 P1.6/AN6 P1.7/AN7 P2.0 RESET P3.2/INT0 P3.1/TxD P3.0/RxD XTAL2 XTAL1 VCC VSS 12 13 14 15 16 17 18 3 4128F-8051-05/06 32 31 30 29 28 27 26 25 P4.1 VAVCC NC VAGND VAREF P1.0/AN 0/T2 P1.1/AN1/T2EX P1.2/AN2/ECI 4 AT89C5115 4128F-8051-05/06 P3.2/INT0 P3.1/TxD P3.0/RxD NC XTAL2 XTAL1 VCC VSS 9 10 11 12 13 14 15 16 P4.0 P2.1 P3.7 P3.6 P3.5/T1 P3.4/T0 NC P3.3/INT1 1 2 3 4 5 6 7 8 QFP-32 24 23 22 21 20 19 17 18 P1.3/AN3/CEX0 P1.4/AN4/CEX1 P1.5/AN5 P1.6/AN6 P1.7/AN7 P2.0 NC RESET AT89C5115 Pin Description Pin Name Type Description VSS VCC VAREF VAVCC VAGND P1.0:7 GND Circuit ground Supply Voltage Reference Voltage for ADC Supply Voltage for ADC Reference Ground for ADC I/O Port 1: Is an 8-bit bi-directional I/O port with internal pull-ups. Port 1 pins can be used for digital input/output or as analog inputs for the Analog Digital Converter (ADC). Port 1 pins that have 1's written to them are pulled high by the internal pull-up transistors and can be used as inputs in this state. As inputs, Port 1 pins that are being pulled low externally will be the source of current (IIL, See section 'Electrical Characteristic') because of the internal pull-ups. Port 1 pins are assigned to be used as analog inputs via the ADCCF register (in this case the internal pull-ups are disconnected). As a secondary digital function, port 1 contains the Timer 2 external trigger and clock input; the PCA external clock input and the PCA module I/O. P1.0/AN0/T2 Analog input channel 0, External clock input for Timer/counter2. P1.1/AN1/T2EX Analog input channel 1, Trigger input for Timer/counter2. P1.2/AN2/ECI Analog input channel 2, PCA external clock input. P1.3/AN3/CEX0 Analog input channel 3, PCA module 0 Entry of input/PWM output. P1.4/AN4/CEX1 Analog input channel 4, PCA module 1 Entry of input/PWM output. P1.5/AN5 Analog input channel 5, P1.6/AN6 Analog input channel 6, P1.7/AN7 Analog input channel 7, It can drive CMOS inputs without external pull-ups. Port 2: Is an 2-bit bi-directional I/O port with internal pull-ups. Port 2 pins that have 1's written to them are pulled high by the internal pull-ups and can be used as inputs in this state. As inputs, Port 2 pins that are being pulled low externally will be a source of current (IIL, on the datasheet) because of the internal pull-ups. In the T89C5115 Port 2 can sink or source 5mA. It can drive CMOS inputs without external pull-ups. P2.0:1 I/O 5 4128F-8051-05/06 Pin Name Type Description P3.0:7 I/O Port 3: Is an 8-bit bi-directional I/O port with internal pull-ups. Port 3 pins that have 1's written to them are pulled high by the internal pull-up transistors and can be used as inputs in this state. As inputs, Port 3 pins that are being pulled low externally will be a source of current (IIL, See section 'Electrical Characteristic') because of the internal pull-ups. The output latch corresponding to a secondary function must be programmed to one for that function to operate (except for TxD and WR). The secondary functions are assigned to the pins of port 3 as follows: P3.0/RxD: Receiver data input (asynchronous) or data input/output (synchronous) of the serial interface P3.1/TxD: Transmitter data output (asynchronous) or clock output (synchronous) of the serial interface P3.2/INT0: External interrupt 0 input/timer 0 gate control input P3.3/INT1: External interrupt 1 input/timer 1 gate control input P3.4/T0: Timer 0 counter input P3.5/T1: Timer 1 counter input P3.6: Regular I/O port pin P3.7: Regular I/O port pin Port 4: Is an 2-bit bi-directional I/O port with internal pull-ups. Port 4 pins that have 1's written to them are pulled high by the internal pull-ups and can be used as inputs in this state. As inputs, Port 4 pins that are being pulled low externally will be a source of current (IIL, on the datasheet) because of the internal pull-up transistor. P4.0: P4.1: It can drive CMOS inputs without external pull-ups. Reset: A high level on this pin during two machine cycles while the oscillator is running resets the device. An internal pull-down resistor to VSS permits power-on reset using only an external capacitor to VCC. XTAL1: Input of the inverting oscillator amplifier and input of the internal clock generator circuits. To drive the device from an external clock source, XTAL1 should be driven, while XTAL2 is left unconnected. To operate above a frequency of 16 MHz, a duty cycle of 50% should be maintained. XTAL2: Output from the inverting oscillator amplifier. P4.0:1 I/O RESET I/O XTAL1 I XTAL2 O 6 AT89C5115 4128F-8051-05/06 AT89C5115 I/O Configurations Each Port SFR operates via type-D latches, as illustrated in Figure 1 for Ports 3 and 4. A CPU 'write to latch' signal initiates transfer of internal bus data into the type-D latch. A CPU 'read latch' signal transfers the latched Q output onto the internal bus. Similarly, a 'read pin' signal transfers the logical level of the Port pin. Some Port data instructions activate the 'read latch' signal while others activate the 'read pin' signal. Latch instructions are referred to as Read-Modify-Write instructions. Each I/O line may be independently programmed as input or output. Figure 1 shows the structure of Ports, which have internal pull-ups. An external source can pull the pin low. Each Port pin can be configured either for general-purpose I/O or for its alternate input output function. To use a pin for general-purpose output, set or clear the corresponding bit in the Px register (x = 1 to 4). To use a pin for general-purpose input, set the bit in the Px register. This turns off the output FET drive. To configure a pin for its alternate function, set the bit in the Px register. When the latch is set, the 'alternate output function' signal controls the output level (See Figure 1). The operation of Ports is discussed further in 'Quasi-Bi-directional Port Operation' paragraph. Figure 1. Ports Structure VCC ALTERNATE OUTPUT FUNCTION Port Structure INTERNAL PULL-UP (1) READ LATCH INTERNAL BUS WRITE TO LATCH D LATCH CL Q P1.x P2.x P3.x P4.x (1) READ PIN ALTERNATE INPUT FUNCTION Note: 1. The internal pull-up can be disabled on P1 when analog function is selected. 7 4128F-8051-05/06 Read-Modify-Write Instructions Some instructions read the latch data rather than the pin data. The latch based instructions read the data, modify the data and then rewrite the latch. These are called 'ReadModify-Write' instructions. Below is a complete list of these special instructions (See Table 1). When the destination operand is a Port or a Port bit, these instructions read the latch rather than the pin: Table 1. Read/Modify/Write Instructions Instruction ANL ORL XRL JBC CPL INC DEC DJNZ MOV Px.y, C CLR Px.y SET Px.y Description Logical AND Logical OR Logical EX-OR Jump if bit = 1 and clear bit Complement bit Increment Decrement Decrement and jump if not zero Move carry bit to bit y of Port x Clear bit y of Port x Set bit y of Port x Example ANL P1, A ORL P2, A XRL P3, A JBC P1.1, LABEL CPL P3.0 INC P2 DEC P2 DJNZ P3, LABEL MOV P1.5, C CLR P2.4 SET P3.3 It is not obvious that the last three instructions in this list are Read-Modify-Write instructions. These instructions read the port (all 8 bits), modify the specifically addressed bit and write the new byte back to the latch. These Read-Modify-Write instructions are directed to the latch rather than the pin in order to avoid possible misinterpretation of voltage (and therefore, logic) levels at the pin. For example, a Port bit used to drive the base of an external bipolar transistor cannot rise above the transistor's base-emitter junction voltage (a value lower than VIL). With a logic one written to the bit, attempts by the CPU to read the Port at the pin are misinterpreted as logic zero. A read of the latch rather than the pins returns the correct logic one value. Quasi Bi-directional Port Operation Port 1, Port 3 and Port 4 have fixed internal pull-ups and are referred to as 'quasi-bidirectional' Ports. When configured as an input, the pin impedance appears as logic one and sources current in response to an external logic zero condition. Resets write logic one to all Port latches. If logical zero is subsequently written to a Port latch, it can be returned to input conditions by a logic one written to the latch. Note: Port latch values change near the end of Read-Modify-Write insruction cycles. Output buffers (and therefore the pin state) are updated early in the instruction after Read-Modify-Write instruction cycle. Logical zero-to-one transitions in Port 1, Port 3 and Port 4 use an additional pull-up (p1) to aid this logic transition See Figure 2. This increases switch speed. This extra pull-up sources 100 times normal internal circuit current during 2 oscillator clock periods. The internal pull-ups are field-effect transistors rather than linear resistors. Pull-ups consist of three p-channel FET (pFET) devices. A pFET is on when the gate senses logic zero and off when the gate senses logic one. pFET #1 is turned on for two oscillator periods immediately after a zero-to-one transition in the Port latch. A logic one at the Port pin turns on pFET #3 (a weak pull-up) through the inverter. This inverter and pFET pair form a latch to drive logic one. pFET #2 is a very weak pull-up switched on whenever the 8 AT89C5115 4128F-8051-05/06 AT89C5115 associated nFET is switched off. This is traditional CMOS switch convention. Current strengths are 1/10 that of pFET #3. Note: During Reset, pFET#1 is not avtivated. During Reset, only the weak pFET#3 pull up the pin. Figure 2. Internal Pull-up Configurations 2 Osc. PERIODS VCC p1(1) VCC p2 VCC p3 P1.x P2.x P3.x P4.x OUTPUT DATA n INPUT DATA READ PIN 9 4128F-8051-05/06 SFR Mapping Tables 3 through Table 11 show the Special Function Registers (SFRs) of the T89C5115. Table 2. C51 Core SFRs Mnemonic ACC B PSW SP Add Name 7 6 5 4 3 2 1 0 E0h Accumulator F0h B Register D0h Program Status Word 81h Stack Pointer Data Pointer Low 82h byte LSB of DPTR Data Pointer High 83h byte MSB of DPTR CY AC F0 RS1 RS0 OV F1 P DPL DPH Table 3. I/O Port SFRs Mnemonic P1 P2 P3 P4 Add Name 7 6 5 4 3 2 1 0 90h Port 1 A0h Port 2 (x2) B0h Port 3 C0h Port 4 (x2) Table 4. Timers SFRs Mnemonic TH0 Add 8Ch Name Timer/Counter 0 High byte Timer/Counter 0 Low byte Timer/Counter 1 High byte Timer/Counter 1 Low byte Timer/Counter 2 High byte Timer/Counter 2 Low byte Timer/Counter 0 and 1 control Timer/Counter 0 and 1 Modes TF1 TR1 TF0 TR0 IE1 IT1 IE0 IT0 7 6 5 4 3 2 1 0 TL0 8Ah TH1 8Dh TL1 8Bh TH2 CDh TL2 CCh TCON 88h TMOD 89h GATE1 C/T1# M11 M01 GATE0 C/T0# M10 M00 10 AT89C5115 4128F-8051-05/06 AT89C5115 Table 4. Timers SFRs (Continued) Mnemonic T2CON Add C8h Name Timer/Counter 2 control Timer/Counter 2 Mode 7 TF2 6 EXF2 5 RCLK 4 TCLK 3 EXEN2 2 TR2 1 C/T2# 0 CP/RL2# T2MOD C9h T2OE DCEN RCAP2H Timer/Counter 2 CBh Reload/Capture High byte Timer/Counter 2 CAh Reload/Capture Low byte A6h WatchDog Timer Reset WatchDog Timer Program S2 S1 S0 RCAP2L WDTRST WDTPRG A7h Table 5. Serial I/O Port SFRs Mnemonic SCON SBUF SADEN SADDR Add Name 7 FE/SM0 6 SM1 5 SM2 4 REN 3 TB8 2 RB8 1 TI 0 RI 98h Serial Control 99h Serial Data Buffer B9h Slave Address Mask A9h Slave Address Table 6. PCA SFRs Mnemonic CCON Add D8h Name PCA Timer/Counter Control PCA Timer/Counter Mode PCA Timer/Counter Low byte PCA Timer/Counter High byte 7 CF 6 CR 5 4 CCF4 3 CCF3 2 CCF2 1 CCF1 0 CCF0 CMOD D9h CIDL CPS1 CPS0 ECF CL E9h CH F9h CCAPM0 CCAPM1 PCA Timer/Counter DAh Mode 0 DBh PCA Timer/Counter Mode 1 PCA Compare FAh Capture Module 0 H FBh PCA Compare Capture Module 1 H ECOM0 ECOM1 CAPP0 CAPP1 CAPN0 CAPN1 MAT0 MAT1 TOG0 TOG1 PWM0 PWM1 ECCF0 ECCF1 CCAP0H CCAP1H CCAP0H7 CCAP1H7 CCAP0H6 CCAP1H6 CCAP0H5 CCAP1H5 CCAP0H4 CCAP1H4 CCAP0H3 CCAP1H3 CCAP0H2 CCAP1H2 CCAP0H1 CCAP1H1 CCAP0H0 CCAP1H0 11 4128F-8051-05/06 Table 6. PCA SFRs (Continued) Mnemonic Add Name 7 6 5 4 3 2 1 0 CCAP0L CCAP1L PCA Compare EAh Capture Module 0 L EBh PCA Compare Capture Module 1 L CCAP0L7 CCAP1L7 CCAP0L6 CCAP1L6 CCAP0L5 CCAP1L5 CCAP0L4 CCAP1L4 CCAP0L3 CCAP1L3 CCAP0L2 CCAP1L2 CCAP0L1 CCAP1L1 CCAP0L0 CCAP1L0 Table 7. Interrupt SFRs Mnemonic IEN0 Add A8h Name Interrupt Enable Control 0 Interrupt Enable Control 1 Interrupt Priority Control Low 0 Interrupt Priority Control High 0 Interrupt Priority Control Low 1 Interrupt Priority Control High1 PPC PT2 PS PT1 PX1 7 EA 6 EC 5 ET2 4 ES 3 ET1 2 EX1 1 ET0 0 EX0 IEN1 E8h EADC IPL0 B8h PT0 PX0 IPH0 B7h PPCH PT2H PSH PT1H PX1H PT0H PX0H IPL1 F8h PADCL IPH1 F7h PADCH Table 8. ADC SFRs Mnemonic ADCON ADCF ADCLK ADDH ADDL Add Name 7 6 PSIDLE CH7 CH6 5 ADEN CH5 4 ADEOC CH4 PRS4 ADAT9 ADAT8 ADAT7 ADAT6 3 ADSST CH3 PRS3 ADAT5 2 SCH2 CH2 PRS2 ADAT4 1 SCH1 CH1 PRS1 ADAT3 ADAT1 0 SCH0 CH0 PRS0 ADAT2 ADAT0 F3h ADC Control F6h ADC Configuration F2h ADC Clock F5h ADC Data High byte F4h ADC Data Low byte Table 9. Other SFRs Mnemonic PCON AUXR1 CKCON FCON EECON Add Name 7 SMOD1 6 SMOD0 ENBOOT WDX2 FPL3 EEPL3 FPL2 EEPL2 PCAX2 FPL1 EEPL1 SIX2 FPL0 EEPL0 5 4 POF 3 GF1 GF3 T2X2 FPS 2 GF0 0 T1X2 FMOD1 T0X2 FMOD0 EEE 1 PD 0 IDL DPS X2 FBUSY EEBUSY 87h Power Control A2h Auxiliary Register 1 8Fh Clock Control D1h Flash Control D2h EEPROM Contol 12 AT89C5115 4128F-8051-05/06 AT89C5115 Table 10. SFR Mapping 0/8(1) F8h IPL1 xxxx xx0x B 0000 0000 IEN1 xxxx xx0x ACC 0000 0000 CCON 0000 0000 PSW 0000 0000 T2CON 0000 0000 P4 xxxx xx11 IPL0 x000 0000 P3 1111 1111 IEN0 0000 0000 P2 xxxx xx11 SCON 0000 0000 P1 1111 1111 TCON 0000 0000 TMOD 0000 0000 SP 0000 0111 0/8(1) 1/9 TL0 0000 0000 DPL 0000 0000 2/A TL1 0000 0000 DPH 0000 0000 3/B 4/C 5/D 6/E TH0 0000 0000 TH1 0000 0000 CKCON 0000 0000 PCON 00x1 0000 7/F SBUF 0000 0000 SADDR 0000 0000 AUXR1(2) xxxx 00x0 WDTRST 1111 1111 WDTPRG xxxx x000 SADEN 0000 0000 IPH0 x000 0000 CMOD 0xxx x000 FCON 0000 0000 T2MOD xxxx xx00 CCAPM0 x000 0000 EECON xxxx xx00 RCAP2L 0000 0000 RCAP2H 0000 0000 TL2 0000 0000 TH2 0000 0000 CCAPM1 x000 0000 CL 0000 0000 1/9 CH 0000 0000 2/A CCAP0H 0000 0000 ADCLK xxx0 0000 CCAP0L 0000 0000 3/B CCAP1H 0000 0000 ADCON x000 0000 CCAP1L 0000 0000 ADDL 0000 0000 ADDH 0000 0000 ADCF 0000 0000 IPH1 xxxx xx0x 4/C 5/D 6/E 7/F FFh F0h F7h E8h EFh E0h E7h D8h DFh D0h D7h C8h CFh C0h C7h B8h BFh B0h B7h A8h AFh A0h A7h 98h 9Fh 90h 97h 88h 8Fh 80h 87h Reserved Notes: 1. These registers are bit-addressable. Sixteen addresses in the SFR space are both byte-addressable and bit-addressable. The bit-addressable SFRs are those whose address ends in 0 and 8. The bit addresses, in this area, are 0x80 through to 0xFF. 2. AUXR1 bit ENBOOT is initialized with the content of the BLJB bit inverted. 13 4128F-8051-05/06 Clock The T89C5115 core needs only 6 clock periods per machine cycle. This feature, called "X2", provides the following advantages: * * * * Divides frequency crystals by 2 (cheaper crystals) while keeping the same CPU power. Saves power consumption while keeping the same CPU power (oscillator power saving). Saves power consumption by dividing dynamic operating frequency by 2 in operating and idle modes. Increases CPU power by 2 while keeping the same crystal frequency. In order to keep the original C51 compatibility, a divider-by-2 is inserted between the XTAL1 signal and the main clock input of the core (phase generator). This divider may be disabled by the software. An extra feature is available to start after Reset in the X2 Mode. This feature can be enabled by a bit X2B in the Hardware Security Byte. This bit is described in the section 'In-System Programming'. Description The X2 bit in the CKCON register (See Table 11) allows switching from 12 clock cycles per instruction to 6 clock cycles and vice versa. At reset, the standard speed is activated (STD mode). Setting this bit activates the X2 feature (X2 Mode) for the CPU Clock only (See Figure 3). The Timers 0, 1 and 2, Uart, PCA, or watchdog switch in X2 Mode only if the corresponding bit is cleared in the CKCON register. The clock for the whole circuit and peripheral is first divided by two before being used by the CPU core and peripherals. This allows any cyclic ratio to be accepted on the XTAL1 input. In X2 Mode, as this divider is bypassed, the signals on XTAL1 must have a cyclic ratio between 40 to 60%. Figure 3. shows the clock generation block diagram. The X2 bit is validated on the XTAL1 / 2 rising edge to avoid glitches when switching from the X2 to the STD mode. Figure 4 shows the mode switching waveforms. 14 AT89C5115 4128F-8051-05/06 AT89C5115 Figure 3. Clock CPU Generation Diagram X2B Hardware byte On RESET PCON.0 IDL X2 CKCON.0 XTAL1 /2 0 1 CPU Core Clock XTAL2 CPU CLOCK PD PCON.1 CPU Core Clock Symbol and ADC 1 2 / / / / / / FT0 Clock X2 CKCON.0 WDX2 CKCON.6 PCAX2 CKCON.5 SIX2 CKCON.4 T2X2 CKCON.3 T1X2 CKCON.2 T0X2 CKCON.1 4128F-8051-05/06 0 1 0 2 FT1 Clock 1 0 2 FT2 Clock FUart Clock 1 0 2 1 0 2 FPca Clock FWd Clock 1 0 2 PERIPH CLOCK Peripheral Clock Symbol 15 Figure 4. Mode Switching Waveforms(1) XTAL1 XTAL2 X2 bit CPU clock STD Mode X2 Mode STD Mode Note: 1. In order to prevent any incorrect operation while operating in the X2 Mode, users must be aware that all peripherals using the clock frequency as a time reference (UART, timers...) will have their time reference divided by 2. For example, a free running timer generating an interrupt every 20 ms will then generate an interrupt every 10 ms. A UART with a 4800 baud rate will have a 9600 baud rate. 16 AT89C5115 4128F-8051-05/06 AT89C5115 Register Table 11. CKCON Register CKCON (S:8Fh) Clock Control Register 7 Bit Number 7 6 WDX2 5 PCAX2 4 SIX2 3 T2X2 2 T1X2 1 T0X2 0 X2 Bit Mnemonic Description Reserved Do not set this bit. Watchdog Clock (1) Clear to select 6 clock periods per peripheral clock cycle. Set to select 12 clock periods per peripheral clock cycle. Programmable Counter Array Clock (1) Clear to select 6 clock periods per peripheral clock cycle. Set to select 12 clock periods per peripheral clock cycle. Enhanced UART clock (MODE 0 and 2) (1) Clear to select 6 clock periods per peripheral clock cycle. Set to select 12 clock periods per peripheral clock cycle. Timer 2 Clock (1) Clear to select 6 clock periods per peripheral clock cycle. Set to select 12 clock periods per peripheral clock cycle. Timer 1 Clock (1) Clear to select 6 clock periods per peripheral clock cycle. Set to select 12 clock periods per peripheral clock cycle. Timer 0 Clock (1) Clear to select 6 clock periods per peripheral clock cycle. Set to select 12 clock periods per peripheral clock cycle. CPU Clock Clear to select 12 clock periods per machine cycle (STD mode) for CPU and all the peripherals. Set to select 6 clock periods per machine cycle (X2 Mode) and to enable the individual peripherals 'X2' bits. 6 WDX2 5 PCAX2 4 SIX2 3 T2X2 2 T1X2 1 T0X2 0 X2 Note: 1. This control bit is validated when the CPU clock bit X2 is set; when X2 is low, this bit has no effect. Reset Value = x000 0000b 17 4128F-8051-05/06 Power Management Two power reduction modes are implemented in the T89C5115: the Idle mode and the Power-down mode. These modes are detailed in the following sections. In addition to these power reduction modes, the clocks of the core and peripherals can be dynamically divided by 2 using the X2 Mode detailed in Section "Clock". In order to start-up (cold reset) or to restart (warm reset) properly the microcontroller, a high level has to be applied on the RST pin. A bad level leads to a wrong initialisation of the internal registers like SFRs, PC, etc. and to unpredictable behavior of the microcontroller. A warm reset can be applied either directly on the RST pin or indirectly by an internal reset source such as a watchdog, PCA, timer, etc. Two conditions are required before enabling a CPU start-up: * * VDD must reach the specified VDD range, The level on xtal1 input must be outside the specification (VIH, VIL). Reset Pin At Power-up (cold reset) If one of these two conditions are not met, the microcontroller does not start correctly and can execute an instruction fetch from anywhere in the program space. An active level applied on the RST pin must be maintained until both of the above conditions are met. A reset is active when the level VIH1 is reached and when the pulse width covers the period of time where VDD and the oscillator are not stabilized. Two parameters have to be taken into account to determine the reset pulse width: * * VDD rise time (vddrst), Oscillator startup time (oscrst). To determine the capacitor the highest value of these two parameters has to be chosen. The reset circuitry is shown in Figure 5. Figure 5. Reset Circuitry VDD Crst RST pin Internal reset Rrst Reset input circuitry 0 Table 12 and Table 13 give some typical examples for three values of VDD rise times, two values of oscillator start-up time and two pull-down resistor values. Table 12. Minimum Reset Capacitor for a 50K Pull-down Resistor oscrst/vddrst 5ms 20ms 1ms 820nF 2.7F 10ms 1.2F 3.9F 100ms 12F 12F 18 AT89C5115 4128F-8051-05/06 AT89C5115 Table 13. Minimum Reset Capacitor for a 15k Pull-down Resistor oscrst/vddrst 5ms 20ms 1ms 2.7F 10F 10ms 4.7F 15F 100ms 47F 47F Note: These values assume VDD starts from 0v to the nominal value. If the time between two on/off sequences is too fast, the power-supply decoupling capacitors may not be fully discharged, leading to a bad reset sequence. During a Normal Operation (Warm Reset) Watchdog Reset Reset pin must be maintained for at least 2 machine cycles (24 oscillator clock periods) to apply a reset sequence during normal operation. The number of clock periods is mode independent (X2 or X1). A 1K resistor must be added in series with the capacitor to allow the use of watchdog reset pulse output on the RST pin or when an external power-supply supervisor is used. Figure 6 shows the reset circuitry when a capacitor is used. Figure 6. Reset Circuitry for a Watchdog Configuration VDD Crst 1k RST pin Internal reset Rrst Reset input circuitry watchdog To other on-board circuitry Figure 7 shows the reset circuitry when an external reset circuit is used. Figure 7. Reset Circuitry Example Using an External Reset Circuit VDD watchdog External reset circuit RST Internal reset Rrst Reset input circuitry 1k RST pin To other on-board circuitry 19 4128F-8051-05/06 Reset Recommendation to Prevent Flash Corruption When a Flash program memory is embedded on-chip, it is strongly recommended to use an external reset chip (brown out device) to apply a reset (Figure 7). It prevents system malfunction during periods of insufficient power-supply voltage (power-supply failure, power supply switched off, etc.). Idle Mode Idle mode is a power reduction mode that reduces the power consumption. In this mode, program execution halts. Idle mode freezes the clock to the CPU at known states while the peripherals continue to be clocked. The CPU status before entering Idle mode is preserved, i.e., the program counter and program status word register retain their data for the duration of Idle mode. The contents of the SFRs and RAM are also retained. The status of the Port pins during Idle mode is detailed in Table 12. To enter Idle mode, set the IDL bit in PCON register (See Table 15). The T89C5115 enters Idle mode upon execution of the instruction that sets IDL bit. The instruction that sets IDL bit is the last instruction executed. Note: If IDL bit and PD bit are set simultaneously, the T89C5115 enters Power-down mode. Then it does not go in Idle mode when exiting Power-down mode. Entering Idle Mode Exiting Idle Mode There are two ways to exit Idle mode: 1. Generate an enabled interrupt. Hardware clears IDL bit in PCON register which restores the clock to the CPU. Execution resumes with the interrupt service routine. Upon completion of the interrupt service routine, program execution resumes with the instruction immediately following the instruction that activated Idle mode. The general purpose flags (GF1 and GF0 in PCON register) may be used to indicate whether an interrupt occurred during normal operation or during Idle mode. When Idle mode is exited by an interrupt, the interrupt service routine may examine GF1 and GF0. 2. Generate a reset. A logic high on the RST pin clears IDL bit in PCON register directly and asynchronously. This restores the clock to the CPU. Program execution momentarily resumes with the instruction immediately following the instruction that activated the Idle mode and may continue for a number of clock cycles before the internal reset algorithm takes control. Reset initializes the T89C5115 and vectors the CPU to address C:0000h. Notes: 1. During the time that execution resumes, the internal RAM cannot be accessed; however, it is possible for the Port pins to be accessed. To avoid unexpected outputs at the Port pins, the instruction immediately following the instruction that activated Idle mode should not write to a Port pin or to the external RAM. 2. If Idle mode is invoked by ADC Idle, the ADC conversion completion will exit Idle. Power-down Mode The Power-down mode places the T89C5115 in a very low power state. Power-down mode stops the oscillator, freezes all clock at known states. The CPU status prior to entering Power-down mode is preserved, i.e., the program counter, program status word register retain their data for the duration of Power-down mode. In addition, the SFRs and RAM contents are preserved. The status of the Port pins during Power-down mode is detailed in Table 14. To enter Power-down mode, set PD bit in PCON register. The T89C5115 enters the Power-down mode upon execution of the instruction that sets PD bit. The instruction that sets PD bit is the last instruction executed. Entering Power-down Mode 20 AT89C5115 4128F-8051-05/06 AT89C5115 Exiting Power-down Mode Note: If VDD was reduced during the Power-down mode, do not exit Power-down mode until VDD is restored to the normal operating level. There are two ways to exit the Power-down mode: 1. Generate an enabled external interrupt. - The T89C5115 provides capability to exit from Power-down using INT0#, INT1#. Hardware clears PD bit in PCON register which starts the oscillator and restores the clocks to the CPU and peripherals. Using INTx# input, execution resumes when the input is released (See Figure 8). Execution resumes with the interrupt service routine. Upon completion of the interrupt service routine, program execution resumes with the instruction immediately following the instruction that activated Power-down mode. 1. The external interrupt used to exit Power-down mode must be configured as level sensitive (INT0# and INT1#) and must be assigned the highest priority. In addition, the duration of the interrupt must be long enough to allow the oscillator to stabilize. The execution will only resume when the interrupt is deasserted. 2. Exit from power-down by external interrupt does not affect the SFRs nor the internal RAM content. Notes: Figure 8. Power-down Exit Waveform Using INT1:0# INT1:0# OSC Active phase Power-down phase Oscillator restart phase Active phase 2. Generate a reset. - A logic high on the RST pin clears PD bit in PCON register directly and asynchronously. This starts the oscillator and restores the clock to the CPU and peripherals. Program execution momentarily resumes with the instruction immediately following the instruction that activated Power-down mode and may continue for a number of clock cycles before the internal reset algorithm takes control. Reset initializes the T89C5115 and vectors the CPU to address 0000h. 1. During the time that execution resumes, the internal RAM cannot be accessed; however, it is possible for the Port pins to be accessed. To avoid unexpected outputs at the Port pins, the instruction immediately following the instruction that activated the Power-down mode should not write to a Port pin or to the external RAM. 2. Exit from power-down by reset redefines all the SFRs, but does not affect the internal RAM content. Notes: 21 4128F-8051-05/06 Table 14. Pin Conditions in Special Operating Modes Mode Reset Idle (internal code) Idle (external code) PowerDown(inter nal code) PowerDown (external code) Port 1 High Port 2 High Port 3 High Port 4 High Data Data Data Data Data Data Data Data Data Data Data Data Data Data Data Data 22 AT89C5115 4128F-8051-05/06 AT89C5115 Registers Table 15. PCON Register PCON (S:87h) Power Control Register 7 SMOD1 Bit Number 7 6 SMOD0 5 4 POF 3 GF1 2 GF0 1 PD 0 IDL Bit Mnemonic Description SMOD1 Serial port Mode bit 1 Set to select double baud rate in mode 1, 2 or 3. Serial port Mode bit 0 Clear to select SM0 bit in SCON register. Set to select FE bit in SCON register. Reserved The value read from this bit is indeterminate. Do not set this bit. Power-off Flag Clear to recognize next reset type. Set by hardware when VCC rises from 0 to its nominal voltage. Can also be set by software. General purpose Flag Cleared by user for general purpose usage. Set by user for general purpose usage. General purpose Flag Cleared by user for general purpose usage. Set by user for general purpose usage. Power-down Mode bit Cleared by hardware when reset occurs. Set to enter power-down mode. Idle Mode bit Clear by hardware when interrupt or reset occurs. Set to enter idle mode. 6 SMOD0 5 - 4 POF 3 GF1 2 GF0 1 PD 0 IDL Reset Value = 00X1 0000b Not bit addressable 23 4128F-8051-05/06 Data Memory The T89C5115 provides data memory access in two different spaces: The internal space mapped in three separate segments: * * * The lower 128 Bytes RAM segment. The upper 128 Bytes RAM segment. The expanded 256 Bytes RAM segment (XRAM). A fourth internal segment is available but dedicated to Special Function Registers, SFRs, (addresses 80h to FFh) accessible by direct addressing mode. Figure 9 shows the internal data memory spaces organization. Figure 9. Internal memory - RAM FFh FFh Upper 128 Bytes Internal RAM Indirect Addressing 80h 7Fh 80h Lower 128 Bytes Internal RAM Direct or Indirect Addressing FFh Special Function Registers Direct Addressing 256 Bytes Internal XRAM 00h 00h Internal Space Lower 128 Bytes RAM The lower 128 Bytes of RAM (See Figure 10) are accessible from address 00h to 7Fh using direct or indirect addressing modes. The lowest 32 Bytes are grouped into 4 banks of 8 registers (R0 to R7). Two bits RS0 and RS1 in PSW register (See Table 17) select which bank is in use according to Table 16. This allows more efficient use of code space, since register instructions are shorter than instructions that use direct addressing, and can be used for context switching in interrupt service routines. Table 16. Register Bank Selection RS1 0 0 1 1 RS0 0 1 0 1 Description Register bank 0 from 00h to 07h Register bank 0 from 08h to 0Fh Register bank 0 from 10h to 17h Register bank 0 from 18h to 1Fh The next 16 Bytes above the register banks form a block of bit-addressable memory space. The C51 instruction set includes a wide selection of singlebit instructions, and the 128 bits in this area can be directly addressed by these instructions. The bit addresses in this area are 00h to 7Fh. 24 AT89C5115 4128F-8051-05/06 AT89C5115 Figure 10. Lower 128 Bytes Internal RAM Organization 7Fh 30h 2Fh 20h 18h 10h 08h 00h 1Fh 17h 0Fh 07h 4 Banks of 8 Registers R0-R7 bit-Addressable Space (bit Addresses 0-7Fh) Upper 128 Bytes RAM The upper 128 Bytes of RAM are accessible from address 80h to FFh using only indirect addressing mode. The on-chip 256 Bytes of expanded RAM (XRAM) are accessible from address 0000h to 00FFh using indirect addressing mode through MOVX instructions. In this address range. Note: Lower 128 Bytes RAM, Upper 128 Bytes RAM, and expanded RAM are made of volatile memory cells. This means that the RAM content is indeterminate after power-up and must then be initialized properly. Expanded RAM 25 4128F-8051-05/06 Dual Data Pointer Description The T89C5115 implements a second data pointer for speeding up code execution and reducing code size in case of intensive usage of external memory accesses. DPTR0 and DPTR1 are Seen by the CPU as DPTR and are accessed using the SFR addresses 83h and 84h that are the DPH and DPL addresses. The DPS bit in AUXR1 register (See Figure 18) is used to select whether DPTR is the data pointer 0 or the data pointer 1 (See Figure 11). Figure 11. Dual Data Pointer Implementation DPL0 DPL1 DPTR0 DPTR1 0 DPL 1 DPS DPH0 DPH1 0 AUXR1.0 DPTR DPH 1 Application Software can take advantage of the additional data pointers to both increase speed and reduce code size, for example, block operations (copy, compare...) are well served by using one data pointer as a "source" pointer and the other one as a "destination" pointer. Hereafter is an example of block move implementation using the two pointers and coded in assembler. The latest C compiler takes also advantage of this feature by providing enhanced algorithm libraries. The INC instruction is a short (2 Bytes) and fast (6 machine cycle) way to manipulate the DPS bit in the AUXR1 register. However, note that the INC instruction does not directly force the DPS bit to a particular state, but simply toggles it. In simple routines, such as the block move example, only the fact that DPS is toggled in the proper sequence matters, not its actual value. In other words, the block move routine works the same whether DPS is 0 or 1 on entry. ; ASCII block move using dual data pointers ; Modifies DPTR0, DPTR1, A and PSW ; Ends when encountering NULL character ; Note: DPS exits opposite to the entry state unless an extra INC AUXR1 is added AUXR1EQU0A2h move:movDPTR,#SOURCE ; address of SOURCE incAUXR1 ; switch data pointers movDPTR,#DEST ; address of DEST mv_loop:incAUXR1; switch data pointers movxA,@DPTR; get a byte from SOURCE incDPTR; increment SOURCE address incAUXR1; switch data pointers movx@DPTR,A; write the byte to DEST incDPTR; increment DEST address jnzmv_loop; check for NULL terminator end_move: 26 AT89C5115 4128F-8051-05/06 AT89C5115 Registers Table 17. PSW Register PSW (S:D0h) Program Status Word Register 7 CY Bit Number 7 6 AC 5 F0 4 RS1 3 RS0 2 OV 1 F1 0 P Bit Mnemonic Description CY Carry Flag Carry out from bit 1 of ALU operands. Auxiliary Carry Flag Carry out from bit 1 of addition operands. User Definable Flag 0 Register Bank Select bits Refer to Table 16 for bits description. Overflow Flag Overflow set by arithmetic operations. User Definable Flag 1 Parity bit Set when ACC contains an odd number of 1's. Cleared when ACC contains an even number of 1's. 6 5 4-3 AC F0 RS1:0 2 1 OV F1 0 P Reset Value = 0000 0000b 27 4128F-8051-05/06 Table 18. AUXR1 Register AUXR1 (S:A2h) Auxiliary Control Register 1 7 Bit Number 7-6 6 Bit Mnemonic 5 ENBOOT 4 3 GF3 2 0 1 0 DPS Description Reserved The value read from these bits is indeterminate. Do not set these bits. 5 Enable Boot Flash ENBOOT(1) Set this bit to map the boot Flash between F800h -FFFFh Clear this bit to disable boot Flash. GF3 Reserved The value read from this bit is indeterminate. Do not set this bit. General Purpose Flag 3 Always Zero This bit is stuck to logic 0 to allow INC AUXR1 instruction without affecting GF3 flag. Reserved for Data Pointer Extension Data Pointer Select bit Set to select second dual data pointer: DPTR1. Clear to select first dual data pointer: DPTR0. 4 3 2 0 1 - 0 DPS Reset Value = XXXX 00X0b Note: 1. ENBOOT is initialized with the invert BLJB at reset. See In-System Programming section. 28 AT89C5115 4128F-8051-05/06 AT89C5115 EEPROM Data Memory The 2K bytes on-chip EEPROM memory block is located at addresses 0000h to 07FFh of the XRAM/XRAM memory space and is selected by setting control bits in the EECON register. A read in the EEPROM memory is done with a MOVX instruction. A physical write in the EEPROM memory is done in two steps: write data in the column latches and transfer of all data latches into an EEPROM memory row (programming). The number of data written on the page may vary from 1 up to 128 Bytes (the page size). When programming, only the data written in the column latch is programmed and a ninth bit is used to obtain this feature. This provides the capability to program the whole memory by Bytes, by page or by a number of Bytes in a page. Indeed, each ninth bit is set when the writing the corresponding byte in a row and all these ninth bits are reset after the writing of the complete EEPROM row. Write Data in the Column Latches Data is written by byte to the column latches as for an external RAM memory. Out of the 11 address bits of the data pointer, the 4 MSBs are used for page selection (row) and 7 are used for byte selection. Between two EEPROM programming sessions, all the addresses in the column latches must stay on the same page, meaning that the 4 MSB must no be changed. The following procedure is used to write to the column latches: * * * * * * * Save and disable interrupt Set bit EEE of EECON register Load DPTR with the address to write Store A register with the data to be written Execute a MOVX @DPTR, A If needed loop the three last instructions until the end of a 128 Bytes page Restore interrupt The last page address used when loading the column latch is the one used to select the page programming address. Note: Programming The EEPROM programming consists of the following actions: * Write one or more Bytes of one page in the column latches. Normally, all Bytes must belong to the same page; if not, the last page address will be latched and the others discarded. Launch programming by writing the control sequence (50h followed by A0h) to the EECON register. EEBUSY flag in EECON is then set by hardware to indicate that programming is in progress and that the EEPROM segment is not available for reading. The end of programming is indicated by a hardware clear of the EEBUSY flag. The sequence 5xh and Axh must be executed without instructions between then otherwise the programming is aborted. * * * Note: Read Data The following procedure is used to read the data stored in the EEPROM memory: * * * * * Save and disable interrupt Set bit EEE of EECON register Load DPTR with the address to read Execute a MOVX A, @DPTR Restore interrupt 29 4128F-8051-05/06 Examples ;*F************************************************************************* ;* NAME: api_rd_eeprom_byte ;* DPTR contain address to read. ;* Acc contain the reading value ;* NOTE: before execute this function, be sure the EEPROM is not BUSY ;*************************************************************************** api_rd_eeprom_byte: ; Save and clear EA MOV MOV ret EECON, #02h; map EEPROM in XRAM space EECON, #00h; unmap EEPROM MOVX A, @DPTR ; Restore EA ;*F************************************************************************* ;* NAME: api_ld_eeprom_cl ;* DPTR contain address to load ;* Acc contain value to load ;* NOTE: in this example we load only 1 byte, but it is possible upto ;* 128 Bytes. ;* before execute this function, be sure the EEPROM is not BUSY ;*************************************************************************** api_ld_eeprom_cl: ; Save and clear EA MOV EECON, #02h ; map EEPROM in XRAM space MOVX @DPTR, A MOVEECON, #00h; unmap EEPROM ; Restore EA ret ;*F************************************************************************* ;* NAME: api_wr_eeprom ;* NOTE: before execute this function, be sure the EEPROM is not BUSY ;*************************************************************************** api_wr_eeprom: ; Save and clear EA MOV MOV ret EECON, #050h EECON, #0A0h ; Restore EA 30 AT89C5115 4128F-8051-05/06 AT89C5115 Registers Table 19. EECON Register EECON (S:0D2h) EEPROM Control Register 7 EEPL3 6 EEPL2 Bit Mnemonic EEPL3-0 5 EEPL1 4 EEPL0 3 2 1 EEE 0 EEBUSY Bit Number 7-4 Description Programming Launch Command bits Write 5Xh followed by AXh to EEPL to launch the programming. Reserved The value read from this bit is indeterminate. Do not set this bit. Reserved The value read from this bit is indeterminate. Do not set this bit. Enable EEPROM Space bit Set to map the EEPROM space during MOVX instructions (Write in the column latches) Clear to map the XRAM space during MOVX. Programming Busy Flag Set by hardware when programming is in progress. Cleared by hardware when programming is done. Can not be set or cleared by software. 3 - 2 - 1 EEE 0 EEBUSY Reset Value = XXXX XX00b Not bit addressable 31 4128F-8051-05/06 Program/Code Memory The T89C5115 implement 16K Bytes of on-chip program/code memory. The Flash memory increases EPROM and ROM functionality by in-circuit electrical erasure and programming. Thanks to the internal charge pump, the high voltage needed for programming or erasing Flash cells is generated on-chip using the standard V DD voltage. Thus, the Flash memory can be programmed using only one voltage and allows InSystem Programming (ISP). Hardware programming mode is also available using specific programming tool. Figure 12. Program/Code Memory Organization 3FFFh 16K Bytes Internal Flash 0000h Flash Memory Architecture T89C5115 features two on-chip Flash memories: * Flash memory FM0: containing 16K Bytes of program memory (user space) organized into 128 bytes pages, Flash memory FM1: 2K Bytes for boot loader and Application Programming Interfaces (API). * The FM0 can be program by both parallel programming and Serial ISP whereas FM1 supports only parallel programming by programmers. The ISP mode is detailed in the 'In-System Programming' section. All Read/Write access operations on Flash memory by user application are managed by a set of API described in the 'In-System Programming' section. Figure 13. Flash Memory Architecture 2K Bytes Flash Memory Boot Space FM1 FFFFh Hardware Security (1 byte) Extra Row (128 Bytes) Column Latches (128 Bytes) F800h 3FFFh 16K Bytes Flash Memory User Space FM0 FM1 mapped between F800h and FFFFh when bit ENBOOT is set in AUXR1 register 0000h 32 AT89C5115 4128F-8051-05/06 AT89C5115 FM0 Memory Architecture The Flash memory is made up of 4 blocks (See Figure 13): 1. The memory array (user space) 16K Bytes 2. The Extra Row 3. The Hardware security bits 4. The column latch registers User Space This space is composed of a 16K Bytes Flash memory organized in 128 pages of 128 Bytes. It contains the user's application code. This row is a part of FM0 and has a size of 128 Bytes. The extra row may contain information for boot loader usage. The Hardware security Byte space is a part of FM0 and has a size of 1 byte. The 4 MSB can be read/written by software, the 4 LSB can only be read by software and written by hardware in parallel mode. The column latches, also part of FM0, have a size of full page (128 Bytes). The column latches are the entrance buffers of the three previous memory locations (user array, XROW and Hardware security byte). The FM0 memory can be programmed as describe on Table 20. Programming FM0 from FM0 is impossible. The FM1 memory can be program only by parallel programming. Table 20 show all software Flash access allowed. Table 20. Cross Flash Memory Access Action Code executing from Read FM0 (user Flash) Load column latch Write Read FM1 (boot Flash) Load column latch Write FM0 (user Flash) ok ok ok ok ok FM1 (boot Flash) ok - Extra Row (XRow) Hardware Security Byte Column Latches Cross Flash Memory Access Description 33 4128F-8051-05/06 Overview of FM0 Operations The CPU interfaces the Flash memory through the FCON register and AUXR1 register. These registers are used to: * * * Map the memory spaces in the adressable space Launch the programming of the memory spaces Get the status of the Flash memory (busy/not busy) Mapping of the Memory Space By default, the user space is accessed by MOVC instruction for read only. The column latches space is made accessible by setting the FPS bit in FCON register. Writing is possible from 0000h to 3FFFh, address bits 6 to 0 are used to select an address within a page while bits 14 to 7 are used to select the programming address of the page. Setting FPS bit takes precedence on the EEE bit in EECON register. The other memory spaces (user, extra row, hardware security) are made accessible in the code segment by programming bits FMOD0 and FMOD1 in FCON register in accordance with Table 21. A MOVC instruction is then used for reading these spaces. Table 21. FM0 blocks Select bits FMOD1 0 0 1 1 FMOD0 0 1 0 1 FM0 Adressable Space User (0000h-3FFFh) Extra Row(FF80h-FFFFh) Hardware Security Byte (0000h) Reserved Launching Programming FPL3:0 bits in FCON register are used to secure the launch of programming. A specific sequence must be written in these bits to unlock the write protection and to launch the programming. This sequence is 5xh followed by Axh. Table 22 summarizes the memory spaces to program according to FMOD1:0 bits. Table 22. Programming Spaces Write to FCON FPL3:0 5 User A 5 Extra Row A Hardware Security Byte Reserved A x 1 1 No action 5 A 5 x x x x 0 1 1 1 1 0 0 1 x x 0 0 0 1 FPS x FMOD1 0 FMOD0 0 Operation No action Write the column latches in user space No action Write the column latches in extra row space No action Write the fuse bits space No action Note: The sequence 5xh and Axh must be executing without instructions between them otherwise the programming is aborted. Interrupts that may occur during programming time must be disabled to avoid any spurious exit of the programming mode. 34 AT89C5115 4128F-8051-05/06 AT89C5115 Status of the Flash Memory The bit FBUSY in FCON register is used to indicate the status of programming. FBUSY is set when programming is in progress. Selecting FM1 Loading the Column Latches The bit ENBOOT in AUXR1 register is used to map FM1 from F800h to FFFFh. Any number of data from 1 byte to 128 Bytes can be loaded in the column latches. This provides the capability to program the whole memory by byte, by page or by any number of Bytes in a page. When programming is launched, an automatic erase of the locations loaded in the column latches is first performed, then programming is effectively done. Thus no page or block erase is needed and only the loaded data are programmed in the corresponding page. The following procedure is used to load the column latches and is summarized in Figure 14: * * * * * * Save then disable interrupt and map the column latch space by setting FPS bit. Load the DPTR with the address to load. Load Accumulator register with the data to load. Execute the MOVX @DPTR, A instruction. If needed loop the three last instructions until the page is completely loaded. unmap the column latch and Restore Interrupt 35 4128F-8051-05/06 Figure 14. Column Latches Loading Procedure(1) Column Latches Loading Save & Disable IT EA = 0 Column Latches Mapping FCON = 08h (FPS = 1) Data Load DPTR = Address ACC = Data Exec: MOVX @DPTR, A Last Byte to load? Data Memory Mapping FCON = 00h (FPS = 0) Restore IT Note: 1. The last page address used when loading the column latch is the one used to select the page programming address. Programming the Flash Spaces User The following procedure is used to program the User space and is summarized in Figure 15: * * * Load up to one page of data in the column latches from address 0000h to 3FFFh. Save then disable the interrupts. Launch the programming by writing the data sequence 50h followed by A0h in FCON register.This step must be executed from FM1. The end of the programming indicated by the FBUSY flag cleared. Restore the interrupts. * Extra Row The following procedure is used to program the Extra Row space and is summarized in Figure 15: * * * Load data in the column latches from address FF80h to FFFFh. Save then disable the interrupts. Launch the programming by writing the data sequence 52h followed by A2h in FCON register. This step of the procedure must be executed from FM1. The end of the programming indicated by the FBUSY flag cleared. Restore the interrupts. * 36 AT89C5115 4128F-8051-05/06 AT89C5115 Figure 15. Flash and Extra row Programming Procedure Flash Spaces Programming Column Latches Loading See Figure 14 Save & Disable IT EA = 0 Launch Programming FCON = 5xh FCON = Axh FBusy Cleared? Clear Mode FCON = 00h End Programming Restore IT Hardware Security Byte The following procedure is used to program the Hardware Security Byte space and is summarized in Figure 16: * * * * * * Set FPS and map Hardware byte (FCON = 0x0C) Save then disable the interrupts. Load DPTR at address 0000h. Load Accumulator register with the data to load. Execute the MOVX @DPTR, A instruction. Launch the programming by writing the data sequence 54h followed by A4h in FCON register. This step of the procedure must be executed from FM1. The end of the programming indicated by the FBusy flag cleared. Restore the interrupts * 37 4128F-8051-05/06 Figure 16. Hardware Programming Procedure Flash Spaces Programming Save & Disable IT EA = 0 Save & Disable IT EA = 0 Launch Programming FCON = 54h FCON = A4h FCON = 0Ch Data Load DPTR = 00h ACC = Data Exec: MOVX @DPTR, A FBusy Cleared? End Loading Restore IT Clear Mode FCON = 00h End Programming RestoreIT Reading the Flash Spaces User The following procedure is used to read the User space: * Read one byte in Accumulator by executing MOVC A,@A+DPTR with A+DPTR is the address of the code byte to read. FCON must be cleared (00h) when not used. Note: Extra Row The following procedure is used to read the Extra Row space and is summarized in Figure 17: * * * Map the Extra Row space by writing 02h in FCON register. Read one byte in Accumulator by executing MOVC A,@A+DPTR with A= 0 & DPTR= FF80h to FFFFh. Clear FCON to unmap the Extra Row. Hardware Security Byte The following procedure is used to read the Hardware Security Byte and is summarized in Figure 17: * * * Map the Hardware Security space by writing 04h in FCON register. Read the byte in Accumulator by executing MOVC A,@A+DPTR with A= 0 & DPTR= 0000h. Clear FCON to unmap the Hardware Security Byte. 38 AT89C5115 4128F-8051-05/06 AT89C5115 Figure 17. Reading Procedure Flash Spaces Reading Flash Spaces Mapping FCON = 00000aa0b Data Read DPTR = Address ACC= 0 Exec: MOVC A, @A+DPTR Clear Mode FCON = 00h Note: aa = 10 for the Hardware Security Byte. Flash Protection from Parallel Programming The three lock bits in Hardware Security Byte (See 'In-System Programming' section) are programmed according to Table 23 provide different level of protection for the onchip code and data located in FM0 and FM1. The only way to write this bits are the parallel mode. They are set by default to level 3. Table 23. Program Lock bit Program Lock bits Security Level 1 2 3 4 LB0 U P U U LB1 U U P U LB2 U U U P Protection Description No program lock features enabled. Parallel programming of the Flash is disabled. Same as 2, also verify through parallel programming interface is disabled. This is the factory defaul programming. Same as 3 Note: 1. Program Lock bits U: unprogrammed P: programmed WARNING: Security level 2, 3 and 4 should only be programmed after Flash and Core verification. Preventing Flash Corruption See Section "Power Management". 39 4128F-8051-05/06 Registers Table 24. FCON Register FCON Register FCON (S:D1h) Flash Control Register 7 FPL3 Bit Number 6 FPL2 5 FPL1 4 FPL0 3 FPS 2 FMOD1 1 FMOD0 0 FBUSY Bit Mnemonic Description Programming Launch Command bits Write 5Xh followed by AXh to launch the programming according to FMOD1:0. (See Table 22.) Flash Map Program Space Set to map the column latch space in the data memory space. Clear to re-map the data memory space. Flash Mode See Table 21 or Table 22. Flash Busy Set by hardware when programming is in progress. Clear by hardware when programming is done. Can not be changed by software. 7-4 FPL3:0 3 FPS 2-1 FMOD1:0 0 FBUSY Reset Value = 0000 0000b 40 AT89C5115 4128F-8051-05/06 AT89C5115 41 4128F-8051-05/06 Operation Cross Memory Access Space addressable in read and write are: * * * * * * * * RAM ERAM (Expanded RAM access by movx) EEPROM DATA FM0 ( user flash ) Hardware byte XROW Boot Flash Flash Column latch The table below provides the different kind of memory which can be accessed from different code location. Table 25. Cross Memory Access Hardware Action Read boot FLASH Write Read FM0 Write OK (idle) OK (1) OK OK) OK(1) OK OK(1) OK OK(1) OK OK(1) RAM ERAM Boot FLASH OK FM0 OK E Data OK Byte OK XROW - Note: 1. RWW: Read While Write 42 AT89C5115 4128F-8051-05/06 AT89C5115 Sharing Instructions Table 26. Instructions shared Action Read Write RAM MOV MOV ERAM MOVX MOVX EEPROM DATA MOVX MOVX Boot FLASH MOVC FM0 MOVC by cl Hardware Byte MOVC by cl XROW MOVC by cl Note: by cl : using Column Latch Table 27. Read MOVX A, @DPTR EEE bit in EECON Register 0 0 1 1 FPS in FCON Register 0 1 0 1 ENBOOT X X X X OK ERAM OK OK OK EEPROM DATA Flash Column Latch Table 28. Write MOVX @DPTR,A EEE bit in EECON Register 0 0 1 1 FPS bit in FCON Register 0 1 0 1 ENBOOT X X X X OK OK ERAM OK OK EEPROM Data Flash Column Latch 43 4128F-8051-05/06 Table 29. Read MOVC A, @DPTR FCON Register Code Execution FMOD1 FMOD0 FPS ENBOOT 0 0 0 X 1 F800h to FFFFh 0 From FM0 1 0 X X 0 1 1 X 1 F800h to FFFFh 0000h to 3FFF 1 0 0 0 1 0 From FM1 (ENBOOT =1 0 1 X 0 1 1 0 X 0 1 1 1 X 0 000h to 3FFFh NA OK X NA 1 X 0000h to 007h See (2) Hardware DPTR 0000h to 3FFFh 0000h to 3FFFh FM1 FM0 OK OK Do not use this configuration OK OK OK OK Do not use this configuration OK OK NA OK NA OK NA OK XROW Byte 1 X X 0000 to 007Fh See (1) X 000h to 3FFFh 0000h to 3FFFh F800h to FFFFh 0 1 X X 1. For DPTR higher than 007Fh only lowest 7 bits are decoded, thus the behavior is the same as for addresses from 0000h to 007Fh 2. For DPTR higher than 007Fh only lowest 7 bits are decoded, thus the behavior is the same as for addresses from 0000h to 007Fh 44 AT89C5115 4128F-8051-05/06 AT89C5115 In-System Programming (ISP) With the implementation of the User Space (FM0) and the Boot Space (FM1) in Flash technology the T89C5115 allows the system engineer the development of applications with a very high level of flexibility. This flexibility is based on the possibility to alter the customer program at any stages of a product's life: * Before mounting the chip on the PCB, FM0 flash can be programmed with the application code. FM1 is always preprogrammed by Atmel with a bootloader (UART bootloader). (1) Once the chip is mounted on the PCB, it can be programmed by serial mode via the UART. 1. The user can also program his own bootloader in FM1. * Note: This ISP allows code modification over the total lifetime of the product. Besides the default Bootloaders Atmel provide customers all the needed ApplicationProgramming-Interfaces (API) which are needed for the ISP. The API are located in the Boot memory. This allow the customer to have a full use of the 16-Kbyte user memory. Flash Programming and Erasure There are three methods for programming the Flash memory: * The Atmel bootloader located in FM1 is activated by the application. Low level API routines (located in FM1)will be used to program FM0. The interface used for serial downloading to FM0 is the UART. API can be called also by user's bootloader located in FM0 at [SBV]00h. A further method exist in activating the Atmel boot loader by hardware activation. See the Section "Hardware Security Byte". The FM0 can be programmed also by the parallel mode using a programmer. * * Figure 18. Flash Memory Mapping FFFFh 2K Bytes IAP Bootloader FM1 F800h 3FFFh Custom Bootloader [SBV]00h 16K Bytes FM1 Mapped between F800h and FFFFh when API Called Flash Memory FM0 0000h 45 4128F-8051-05/06 Boot Process Software Boot Process Example Many algorithms can be used for the software boot process. Below are descriptions of the different flags and Bytes. Boot Loader Jump bit (BLJB): - This bit indicates if on RESET the user wants to jump to this application at address @0000h on FM0 or execute the boot loader at address @F800h on FM1. - BLJB = 0 (i.e. bootloader FM1 executed after a reset) is the default Atmel factory programming. -To read or modify this bit, the APIs are used. Boot Vector Address (SBV): - This byte contains the MSB of the user boot loader address in FM0. - The default value of SBV is FCh (no user boot loader in FM0). - To read or modify this byte, the APIs are used. Extra Byte (EB) & Boot Status Byte (BSB): - These Bytes are reserved for customer use. - To read or modify these Bytes, the APIs are used. Figure 19. Hardware Boot Process Algorithm RESET bit ENBOOT in AUXR1 Register Is Initialized with BLJB Inverted. Example, if BLJB=0, ENBOOT Hardware ENBOOT = 0 PC = 0000h BLJB == 0 ? is set (=1) during reset, thus the bootloader is executed after the reset. ENBOOT = 1 PC = F800h Software Application in FM0 Bootloader in FM1 ApplicationProgramming-Interface Several Application Program Interface (API) calls are available for use by an application program to permit selective erasing and programming of Flash pages. All calls are made by functions. All these APIs are described in detail in the following documents on the Atmel web site. - Datasheet Bootloader UART T89C5115. 46 AT89C5115 4128F-8051-05/06 AT89C5115 XROW Bytes The EXTRA ROW (XROW) includes 128 bytes. Some of these bytes are used for specific purpose in conjonction with the bootloader. Table 30. XROW Mapping Description Copy of the Manufacturer Code Copy of the Device ID#1: Family code Copy of the Device ID#2: Memories size and type Copy of the Device ID#3: Name and Revision Default Value 58h D7h BBh FFh Address 30h 31h 60h 61h Hardware Conditions It is possible to force the controller to execute the bootloader after a Reset with hardware conditions. During the first programming, the user can define a configuration on Port1 that will be recognized by the chip as the hardware conditions during a Reset. If this condition is met, the chip will start executing the bootloader at the end of the Reset. See a detailed description in the applicable Document. - - Datasheet Bootloader UART T89C5115. 47 4128F-8051-05/06 Hardware Security Byte Table 31. Hardware Security byte 7 X2B Bit Number 6 BLJB 5 4 3 2 LB2 1 LB1 0 LB0 Bit Mnemonic Description X2 bit Set this bit to start in standard mode Clear this bit to start in X2 Mode. Boot Loader Jump bit - 1: To start the user's application on next RESET (@0000h) located in FM0, - 0: To start the boot loader(@F800h) located in FM1. Reserved The value read from these bits are indeterminate. Lock bits (see Table 22) 7 X2B 6 BLJB 5-3 2-0 LB2:0 After erasing the chip in parallel mode, the default value is : FFh The erasing in ISP mode (from bootloader) does not modify this byte. Notes: 1. Only the 4 MSB bits can be accessed by software. 2. The 4 LSB bits can only be accessed by parallel mode. 48 AT89C5115 4128F-8051-05/06 AT89C5115 Serial I/O Port The T89C5115 I/O serial port is compatible with the I/O serial port in the 80C52. It provides both synchronous and asynchronous communication modes. It operates as a Universal Asynchronous Receiver and Transmitter (UART) in three full-duplex modes (Modes 1, 2 and 3). Asynchronous transmission and reception can occur simultaneously and at different baud rates Serial I/O port includes the following enhancements: * * Framing error detection Automatic address recognition Figure 20. Serial I/O Port Block Diagram IB Bus Write SBUF SBUF Receiver Read SBUF TXD SBUF Transmitter Mode 0 Transmit Load SBUF RXD Receive Shift register Serial Port Interrupt Request RI TI SCON reg Framing Error Detection Framing bit error detection is provided for the three asynchronous modes. To enable the framing bit error detection feature, set SMOD0 bit in PCON register. Figure 21. Framing Error Block Diagram SM0/FE SM1 SM2 REN TB8 RB8 TI RI Set FE bit if Stop bit is 0 (Framing Error) SM0 to UART Mode Control SMOD1 SMOD0 - POF GF1 GF0 PD IDL To UART Framing Error Control When this feature is enabled, the receiver checks each incoming data frame for a valid stop bit. An invalid stop bit may result from noise on the serial lines or from simultaneous transmission by two CPUs. If a valid stop bit is not found, the Framing Error bit (FE) in SCON register bit is set. The software may examine the FE bit after each reception to check for data errors. Once set, only software or a reset clears the FE bit. Subsequently received frames with valid stop bits cannot clear the FE bit. When the FE feature is enabled, RI rises on the stop bit instead of the last data bit (See Figure 22 and Figure 23). 49 4128F-8051-05/06 Figure 22. UART Timing in Mode 1 RXD Start bit RI SMOD0 = x FE SMOD0 = 1 D0 D1 D2 D3 D4 D5 D6 D7 Stop bit Data Byte Figure 23. UART Timing in Modes 2 and 3 RXD Start bit RI SMOD0 = 0 RI SMOD0 = 1 FE SMOD0 = 1 D0 D1 D2 D3 D4 D5 D6 D7 D8 Ninth Stop bit bit Data Byte Automatic Address Recognition The automatic address recognition feature is enabled when the multiprocessor communication feature is enabled (SM2 bit in SCON register is set). Implemented in the hardware, automatic address recognition enhances the multiprocessor communication feature by allowing the serial port to examine the address of each incoming command frame. Only when the serial port recognizes its own address will the receiver set the RI bit in the SCON register to generate an interrupt. This ensures that the CPU is not interrupted by command frames addressed to other devices. If necessary, the user can enable the automatic address recognition feature in mode 1. In this configuration, the stop bit takes the place of the ninth data bit. bit RI is set only when the received command frame address matches the device's address and is terminated by a valid stop bit. To support automatic address recognition, a device is identified by a given address and a broadcast address. Note: The multiprocessor communication and automatic address recognition features cannot be enabled in mode 0 (i.e. setting SM2 bit in SCON register in mode 0 has no effect). Given Address Each device has an individual address that is specified in the SADDR register; the SADEN register is a mask byte that contains don't-care bits (defined by zeros) to form the device's given address. The don't-care bits provide the flexibility to address one or more slaves at a time. The following example illustrates how a given address is formed. To address a device by its individual address, the SADEN mask byte must be 1111 1111b. For example: SADDR0101 0110b SADEN1111 1100b Given0101 01XXb 50 AT89C5115 4128F-8051-05/06 AT89C5115 Here is an example of how to use given addresses to address different slaves: Slave A:SADDR1111 0001b SADEN1111 1010b Given1111 0X0Xb Slave B:SADDR1111 0011b SADEN1111 1001b Given1111 0XX1b Slave C:SADDR1111 0011b SADEN1111 1101b Given1111 00X1b The SADEN byte is selected so that each slave may be addressed separately. For slave A, bit 0 (the LSB) is a don't-care bit; for slaves B and C, bit 0 is a 1. To communicate with slave A only, the master must send an address where bit 0 is clear (e.g. 1111 0000b). For slave A, bit 1 is a 0; for slaves B and C, bit 1 is a don't care bit. To communicate with slaves A and B, but not slave C, the master must send an address with bits 0 and 1 both set (e.g. 1111 0011b). To communicate with slaves A, B and C, the master must send an address with bit 0 set, bit 1 clear, and bit 2 clear (e.g. 1111 0001b). Broadcast Address A broadcast address is formed from the logical OR of the SADDR and SADEN registers with zeros defined as don't-care bits, e.g.: SADDR 0101 0110b SADEN 1111 1100b SADDR OR SADEN1111 111Xb The use of don't-care bits provides flexibility in defining the broadcast address, however in most applications, a broadcast address is FFh. The following is an example of using broadcast addresses: Slave A:SADDR1111 0001b SADEN1111 1010b Given1111 1X11b, Slave B:SADDR1111 0011b SADEN1111 1001b Given1111 1X11B, Slave C:SADDR=1111 0010b SADEN1111 1101b Given1111 1111b For slaves A and B, bit 2 is a don't care bit; for slave C, bit 2 is set. To communicate with all of the slaves, the master must send an address FFh. To communicate with slaves A and B, but not slave C, the master can send and address FBh. 51 4128F-8051-05/06 Registers Table 32. SCON Register SCON (S:98h) Serial Control Register 7 FE/SM0 Bit Number 6 SM1 5 SM2 4 REN 3 TB8 2 RB8 1 TI 0 RI Bit Mnemonic Description Framing Error bit (SMOD0 = 1) Clear to reset the error state, not cleared by a valid stop bit. Set by hardware when an invalid stop bit is detected. Serial port Mode bit 0 (SMOD0 = 0) Refer to SM1 for serial port mode selection. Serial port Mode bit 1 SM0 SM1 Mode 0 0 Shift Register 0 1 8-bit UART 1 0 9bit UART 1 1 9bit UART 7 FE SM0 6 SM1 Baud Rate FXTAL/12 (or FXTAL/6 in mode X2) Variable FXTAL/64 or FXTAL/32 Variable 5 SM2 Serial port Mode 2 bit/Multiprocessor Communication Enable bit Clear to disable multiprocessor communication feature. Set to enable multiprocessor communication feature in mode 2 and 3. Reception Enable bit Clear to disable serial reception. Set to enable serial reception. Transmitter bit 8/Ninth bit to Transmit in Modes 2 and 3 Clear to transmit a logic 0 in the 9th bit. Set to transmit a logic 1 in the 9th bit. Receiver bit 8/Ninth bit Received in Modes 2 and 3 Cleared by hardware if 9th bit received is a logic 0. Set by hardware if 9th bit received is a logic 1. Transmit Interrupt Flag Clear to acknowledge interrupt. Set by hardware at the end of the 8th bit time in mode 0 or at the beginning of the stop bit in the other modes. Receive Interrupt Flag Clear to acknowledge interrupt. Set by hardware at the end of the 8th bit time in mode 0, See Figure 22. and Figure 23. in the other modes. 4 REN 3 TB8 2 RB8 1 TI 0 RI Reset Value = 0000 0000b bit addressable 52 AT89C5115 4128F-8051-05/06 AT89C5115 Table 33. SADEN Register SADEN (S:B9h) Slave Address Mask Register 7 6 5 4 3 2 1 0 Bit Number 7-0 Bit Mnemonic Description Mask Data for Slave Individual Address Reset Value = 0000 0000b Not bit addressable Table 34. SADDR Register SADDR (S:A9h) Slave Address Register 7 6 5 4 3 2 1 0 Bit Number 7-0 Bit Mnemonic Description Slave Individual Address Reset Value = 0000 0000b Not bit addressable Table 35. SBUF Register SBUF (S:99h) Serial Data Buffer 7 6 5 4 3 2 1 0 Bit Number 7-0 Bit Mnemonic Description Data sent/received by Serial I/O Port Reset Value = 0000 0000b Not bit addressable 53 4128F-8051-05/06 Table 36. PCON Register PCON (S:87h) Power Control Register 7 SMOD1 Bit Number 7 6 SMOD0 5 4 POF 3 GF1 2 GF0 1 PD 0 IDL Bit Mnemonic Description SMOD1 Serial port Mode bit 1 Set to select double baud rate in mode 1, 2 or 3. Serial port Mode bit 0 Clear to select SM0 bit in SCON register. Set to select FE bit in SCON register. Reserved The value read from this bit is indeterminate. Do not set this bit. Power-off Flag Clear to recognize next reset type. Set by hardware when VCC rises from 0 to its nominal voltage. Can also be set by software. General purpose Flag Cleared by user for general purpose usage. Set by user for general purpose usage. General purpose Flag Cleared by user for general purpose usage. Set by user for general purpose usage. Power-down Mode bit Cleared by hardware when reset occurs. Set to enter power-down mode. Idle Mode bit Clear by hardware when interrupt or reset occurs. Set to enter idle mode. 6 SMOD0 5 - 4 POF 3 GF1 2 GF0 1 PD 0 IDL Reset Value = 00X1 0000b Not bit addressable 54 AT89C5115 4128F-8051-05/06 AT89C5115 Timers/Counters The T89C5115 implements two general-purpose, 16-bit Timers/Counters. Such are identified as Timer 0 and Timer 1, and can be independently configured to operate in a variety of modes as a Timer or an event Counter. When operating as a Timer, the Timer/Counter runs for a programmed length of time, then issues an interrupt request. When operating as a Counter, the Timer/Counter counts negative transitions on an external pin. After a preset number of counts, the Counter issues an interrupt request. The various operating modes of each Timer/Counter are described in the following sections. A basic operation is Timer registers THx and TLx (x = 0, 1) connected in cascade to form a 16-bit Timer. Setting the run control bit (TRx) in TCON register (See Figure 37) turns the Timer on by allowing the selected input to increment TLx. When TLx overflows it increments THx; when THx overflows it sets the Timer overflow flag (TFx) in TCON register. Setting the TRx does not clear the THx and TLx Timer registers. Timer registers can be accessed to obtain the current count or to enter preset values. They can be read at any time but TRx bit must be cleared to preset their values, otherwise the behavior of the Timer/Counter is unpredictable. The C/Tx# control bit selects Timer operation or Counter operation by selecting the divided-down peripheral clock or external pin Tx as the source for the counted signal. TRx bit must be cleared when changing the mode of operation, otherwise the behavior of the Timer/Counter is unpredictable. For Timer operation (C/Tx# = 0), the Timer register counts the divided-down peripheral clock. The Timer register is incremented once every peripheral cycle (6 peripheral clock periods). The Timer clock rate is fPER/6, i.e. fOSC/12 in standard mode or fOSC/6 in X2 Mode. For Counter operation (C/Tx# = 1), the Timer register counts the negative transitions on the Tx external input pin. The external input is sampled every peripheral cycles. When the sample is high in one cycle and low in the next one, the Counter is incremented. Since it takes 2 cycles (12 peripheral clock periods) to recognize a negative transition, the maximum count rate is fPER/12, i.e. fOSC/24 in standard mode or f OSC/12 in X2 Mode. There are no restrictions on the duty cycle of the external input signal, but to ensure that a given level is sampled at least once before it changes, it should be held for at least one full peripheral cycle. Timer/Counter Operations Timer 0 Timer 0 functions as either a Timer or event Counter in four modes of operation. Figure 24 through Figure 27 show the logical configuration of each mode. Timer 0 is controlled by the four lower bits of TMOD register (See Figure 38) and bits 0, 1, 4 and 5 of TCON register (See Figure 37). TMOD register selects the method of Timer gating (GATE0), Timer or Counter operation (T/C0#) and mode of operation (M10 and M00). TCON register provides Timer 0 control functions: overflow flag (TF0), run control bit (TR0), interrupt flag (IE0) and interrupt type control bit (IT0). For normal Timer operation (GATE0 = 0), setting TR0 allows TL0 to be incremented by the selected input. Setting GATE0 and TR0 allows external pin INT0# to control Timer operation. Timer 0 overflow (count rolls over from all 1s to all 0s) sets TF0 flag generating an interrupt request. It is important to stop Timer/Counter before changing mode. 55 4128F-8051-05/06 Mode 0 (13-bit Timer) Mode 0 configures Timer 0 as an 13-bit Timer which is set up as an 8-bit Timer (TH0 register) with a modulo 32 prescaler implemented with the lower five bits of TL0 register (See Figure 24). The upper three bits of TL0 register are indeterminate and should be ignored. Prescaler overflow increments TH0 register. Figure 24. Timer/Counter x (x= 0 or 1) in Mode 0 See section "Clock" FTx CLOCK /6 0 1 THx (8 bits) TLx (5 bits) Overflow TFx TCON Reg Tx C/Tx# TMOD Reg Timer x Interrupt Request INTx# GATEx TMOD Reg TRx TCON Reg Mode 1 (16-bit Timer) Mode 1 configures Timer 0 as a 16-bit Timer with TH0 and TL0 registers connected in cascade (See Figure 25). The selected input increments TL0 register. Figure 25. Timer/Counter x (x= 0 or 1) in Mode 1 See section "Clock" FTx CLOCK /6 0 1 THx (8 bits) TLx (8 bits) Overflow TFx TCON Reg Tx C/Tx# TMOD Reg Timer x Interrupt Request INTx# GATEx TMOD Reg TRx TCON Reg Mode 2 (8-bit Timer with AutoReload) Mode 2 configures Timer 0 as an 8-bit Timer (TL0 register) that automatically reloads from TH0 register (See Figure 26). TL0 overflow sets TF0 flag in TCON register and reloads TL0 with the contents of TH0, which is preset by software. When the interrupt request is serviced, hardware clears TF0. The reload leaves TH0 unchanged. The next reload value may be changed at any time by writing it to TH0 register. 56 AT89C5115 4128F-8051-05/06 AT89C5115 Figure 26. Timer/Counter x (x= 0 or 1) in Mode 2 See section "Clock" FTx CLOCK /6 0 1 TLx (8 bits) Overflow TFx TCON Reg Tx C/Tx# TMOD Reg Timer x Interrupt Request INTx# GATEx TMOD Reg TRx TCON Reg THx (8 bits) Mode 3 (Two 8-bit Timers) Mode 3 configures Timer 0 such that registers TL0 and TH0 operate as separate 8-bit Timers (See Figure 27). This mode is provided for applications requiring an additional 8bit Timer or Counter. TL0 uses the Timer 0 control bits C/T0# and GATE0 in TMOD register, and TR0 and TF0 in TCON register in the normal manner. TH0 is locked into a Timer function (counting FPER /6) and takes over use of the Timer 1 interrupt (TF1) and run control (TR1) bits. Thus, operation of Timer 1 is restricted when Timer 0 is in mode 3. Figure 27. Timer/Counter 0 in Mode 3: Two 8-bit Counters FTx CLOCK /6 0 1 TL0 (8 bits) Overflow TF0 TCON.5 T0 C/T0# TMOD.2 Timer 0 Interrupt Request INT0# GATE0 TMOD.3 TR0 TCON.4 FTx CLOCK /6 TH0 (8 bits) TR1 TCON.6 Overflow TF1 TCON.7 Timer 1 Interrupt Request See section "Clock" Timer 1 Timer 1 is identical to Timer 0 excepted for Mode 3 which is a hold-count mode. Following comments help to understand the differences: * Timer 1 functions as either a Timer or event Counter in three modes of operation. Figure 24 to Figure 26 show the logical configuration for modes 0, 1, and 2. Timer 1's mode 3 is a hold-count mode. Timer 1 is controlled by the four high-order bits of TMOD register (See Figure 38) and bits 2, 3, 6 and 7 of TCON register (See Figure 37). TMOD register selects the method of Timer gating (GATE1), Timer or Counter operation (C/T1#) and mode of operation (M11 and M01). TCON register provides Timer 1 control functions: overflow flag (TF1), run control bit (TR1), interrupt flag (IE1) and interrupt type control bit (IT1). Timer 1 can serve as the Baud Rate Generator for the Serial Port. Mode 2 is best suited for this purpose. 57 * * 4128F-8051-05/06 * For normal Timer operation (GATE1= 0), setting TR1 allows TL1 to be incremented by the selected input. Setting GATE1 and TR1 allows external pin INT1# to control Timer operation. Timer 1 overflow (count rolls over from all 1s to all 0s) sets the TF1 flag generating an interrupt request. When Timer 0 is in mode 3, it uses Timer 1's overflow flag (TF1) and run control bit (TR1). For this situation, use Timer 1 only for applications that do not require an interrupt (such as a Baud Rate Generator for the Serial Port) and switch Timer 1 in and out of mode 3 to turn it off and on. It is important to stop Timer/Counter before changing mode. * * * Mode 0 (13-bit Timer) Mode 0 configures Timer 1 as a 13-bit Timer, which is set up as an 8-bit Timer (TH1 register) with a modulo-32 prescaler implemented with the lower 5 bits of the TL1 register (See Figure 24). The upper 3 bits of TL1 register are ignored. Prescaler overflow increments TH1 register. Mode 1 configures Timer 1 as a 16-bit Timer with TH1 and TL1 registers connected in cascade (See Figure 25). The selected input increments TL1 register. Mode 2 configures Timer 1 as an 8-bit Timer (TL1 register) with automatic reload from TH1 register on overflow (See Figure 26). TL1 overflow sets TF1 flag in TCON register and reloads TL1 with the contents of TH1, which is preset by software. The reload leaves TH1 unchanged. Placing Timer 1 in mode 3 causes it to halt and hold its count. This can be used to halt Timer 1 when TR1 run control bit is not available i.e. when Timer 0 is in mode 3. Each Timer handles one interrupt source that is the timer overflow flag TF0 or TF1. This flag is set every time an overflow occurs. Flags are cleared when vectoring to the Timer interrupt routine. Interrupts are enabled by setting ETx bit in IEN0 register. This assumes interrupts are globally enabled by setting EA bit in IEN0 register. Figure 28. Timer Interrupt System TF0 TCON.5 Mode 1 (16-bit Timer) Mode 2 (8-bit Timer with AutoReload) Mode 3 (Halt) Interrupt Timer 0 Interrupt Request ET0 IEN0.1 TF1 TCON.7 Timer 1 Interrupt Request ET1 IEN0.3 58 AT89C5115 4128F-8051-05/06 AT89C5115 Registers Table 37. TCON Register TCON (S:88h) Timer/Counter Control Register 7 TF1 Bit Number 6 TR1 5 TF0 4 TR0 3 IE1 2 IT1 1 IE0 0 IT0 Bit Mnemonic Description Timer 1 Overflow Flag Cleared by hardware when processor vectors to interrupt routine. Set by hardware on Timer/Counter overflow, when Timer 1 register overflows. Timer 1 Run Control bit Clear to turn off Timer/Counter 1. Set to turn on Timer/Counter 1. Timer 0 Overflow Flag Cleared by hardware when processor vectors to interrupt routine. Set by hardware on Timer/Counter overflow, when Timer 0 register overflows. Timer 0 Run Control bit Clear to turn off Timer/Counter 0. Set to turn on Timer/Counter 0. Interrupt 1 Edge Flag Cleared by hardware when interrupt is processed if edge-triggered (See IT1). Set by hardware when external interrupt is detected on INT1# pin. Interrupt 1 Type Control bit Clear to select low level active (level triggered) for external interrupt 1 (INT1#). Set to select falling edge active (edge triggered) for external interrupt 1. Interrupt 0 Edge Flag Cleared by hardware when interrupt is processed if edge-triggered (See IT0). Set by hardware when external interrupt is detected on INT0# pin. Interrupt 0 Type Control bit Clear to select low level active (level triggered) for external interrupt 0 (INT0#). Set to select falling edge active (edge triggered) for external interrupt 0. 7 TF1 6 TR1 5 TF0 4 TR0 3 IE1 2 IT1 1 IE0 0 IT0 Reset Value = 0000 0000b 59 4128F-8051-05/06 Table 38. TMOD Register TMOD (S:89h) Timer/Counter Mode Control Register 7 GATE1 6 C/T1# 5 M11 4 M01 3 GATE0 2 C/T0# 1 M10 0 M00 Bit Number Bit Mnemonic Description Timer 1 Gating Control bit Clear to enable Timer 1 whenever TR1 bit is set. Set to enable Timer 1 only while INT1# pin is high and TR1 bit is set. Timer 1 Counter/Timer Select bit Clear for Timer operation: Timer 1 counts the divided-down system clock. Set for Counter operation: Timer 1 counts negative transitions on external pin T1. Timer 1 Mode Select bits M11 M01 Operating mode 0 0 Mode 0: 8-bit Timer/Counter (TH1) with 5bit prescaler (TL1). 0 1 Mode 1: 16-bit Timer/Counter. 1 1 1 0 Mode 3: Timer 1 halted. Retains count. Mode 2: 8-bit auto-reload Timer/Counter (TL1).(1) 7 GATE1 6 C/T1# 5 M11 4 M01 3 GATE0 Timer 0 Gating Control bit Clear to enable Timer 0 whenever TR0 bit is set. Set to enable Timer/Counter 0 only while INT0# pin is high and TR0 bit is set. Timer 0 Counter/Timer Select bit Clear for Timer operation: Timer 0 counts the divided-down system clock. Set for Counter operation: Timer 0 counts negative transitions on external pin T0. Timer 0 Mode Select bit M10 M00 Operating mode 0 0 Mode 0: 8-bit Timer/Counter (TH0) with 5bit prescaler (TL0). 0 1 Mode 1: 16-bit Timer/Counter. 1 0 Mode 2: 8-bit auto-reload Timer/Counter (TL0).(2) 1 1 Mode 3: TL0 is an 8-bit Timer/Counter. TH0 is an 8-bit Timer using Timer 1's TR0 and TF0 bits. 2 C/T0# 1 M10 0 M00 Reset Value = 0000 0000b Notes: 1. Reloaded from TH1 at overflow. 2. Reloaded from TH0 at overflow. Table 39. TH0 Register TH0 (S:8Ch) Timer 0 High Byte Register 7 6 5 4 3 2 1 0 Bit Number 7:0 Bit Mnemonic Description High Byte of Timer 0 Reset Value = 0000 0000b 60 AT89C5115 4128F-8051-05/06 AT89C5115 Table 40. TL0 Register TL0 (S:8Ah) Timer 0 Low Byte Register 7 6 5 4 3 2 1 0 Bit Number 7:0 Bit Mnemonic Description Low Byte of Timer 0 Reset Value = 0000 0000b Table 41. TH1 Register TH1 (S:8Dh) Timer 1 High Byte Register 7 6 5 4 3 2 1 0 Bit Number 7:0 Bit Mnemonic Description High Byte of Timer 1 Reset Value = 0000 0000b Table 42. TL1 Register TL1 (S:8Bh) Timer 1 Low Byte Register 7 6 5 4 3 2 1 0 Bit Number 7:0 Bit Mnemonic Description Low Byte of Timer 1 Reset Value = 0000 0000b 61 4128F-8051-05/06 Timer 2 The T89C5115 Timer 2 is compatible with Timer 2 in the 80C52. It is a 16-bit timer/counter: the count is maintained by two eightbit timer registers, TH2 and TL2 that are cascade-connected. It is controlled by T2CON register (See Table 44) and T2MOD register (See Table 45). Timer 2 operation is similar to Timer 0 and Timer 1. C/T2 selects F T2 clock/6 (timer operation) or external pin T2 (counter operation) as timer clock. Setting TR2 allows TL2 to be incremented by the selected input. Timer 2 includes the following enhancements: * * Auto-reload mode (up or down counter) Programmable clock-output Auto-Reload Mode The auto-reload mode configures Timer 2 as a 16-bit timer or event counter with automatic reload. This feature is controlled by the DCEN bit in T2MOD register (See Table 44). Setting the DCEN bit enables Timer 2 to count up or down as shown in Figure 29. In this mode the T2EX pin controls the counting direction. When T2EX is high, Timer 2 counts up. Timer overflow occurs at FFFFh which sets the TF2 flag and generates an interrupt request. The overflow also causes the 16-bit value in RCAP2H and RCAP2L registers to be loaded into the timer registers TH2 and TL2. When T2EX is low, Timer 2 counts down. Timer underflow occurs when the count in the timer registers TH2 and TL2 equals the value stored in RCAP2H and RCAP2L registers. The underflow sets TF2 flag and reloads FFFFh into the timer registers. The EXF2 bit toggles when Timer 2 overflow or underflow, depending on the direction of the count. EXF2 does not generate an interrupt. This bit can be used to provide 17-bit resolution. Figure 29. Auto-Reload Mode Up/Down Counter See section "Clock" FT2 CLOCK :6 0 1 TR2 T2CON.2 CT/2 T2CON.1 T2 (DOWN COUNTING RELOAD VALUE) T2EX: FFh (8-bit) FFh (8-bit) 1=UP 2=DOWN TOGGLE T2CON Reg EXF2 TL2 (8-bit) TH2 (8-bit) TIMER 2 INTERRUPT T2CON Reg TF2 RCAP2L (8-bit) RCAP2H (8-bit) (UP COUNTING RELOAD VALUE) 62 AT89C5115 4128F-8051-05/06 AT89C5115 Programmable ClockOutput In clock-out mode, Timer 2 operates as a 50%-duty-cycle, programmable clock generator (Figure 30). The input clock increments TL2 at frequency f OSC /2. The timer repeatedly counts to overflow from a loaded value. At overflow, the contents of RCAP2H and RCAP2L registers are loaded into TH2 and TL2. In this mode, Timer 2 overflows do not generate interrupts. The formula gives the clock-out frequency depending on the system oscillator frequency and the value in the RCAP2H and RCAP2L registers: - - ------------------------------------------- = -------------------------------------------- 4 x ( 65536 For a 16 MHz system clock in x1 mode, Timer 2 has a programmable frequency range of 61 Hz (fOSC/216) to 4 MHz (fOSC/4). The generated clock signal is brought out to T2 pin (P1.0). Timer 2 is programmed for the clock-out mode as follows: * * * * * Set T2OE bit in T2MOD register. Clear C/T2 bit in T2CON register. Determine the 16-bit reload value from the formula and enter it in RCAP2H/RCAP2L registers. Enter a 16-bit initial value in timer registers TH2/TL2. It can be the same as the reload value or different depending on the application. To start the timer, set TR2 run control bit in T2CON register. It is possible to use Timer 2 as a baud rate generator and a clock generator simultaneously. For this configuration, the baud rates and clock frequencies are not independent since both functions use the values in the RCAP2H and RCAP2L registers. Figure 30. Clock-Out Mode FT2 CLOCK TL2 (8-bit) TH2 (8-bit) OVERFLOW TR2 T2CON.2 RCAP2L RCAP2H (8-bit) (8-bit) Toggle T2 Q Q D T2OE T2MOD reg T2EX EXEN2 T2CON reg EXF2 T2CON reg 4128F-8051-05/06 L PA C R H P A C R k co l c T F 2 TIMER 2 INTERRUPT 2 y cn euq e r F tu O - k co l C 2) 63 Registers Table 43. T2CON Register T2CON (S:C8h) Timer 2 Control Register 7 TF2 Bit Number 6 EXF2 5 RCLK 4 TCLK 3 EXEN2 2 TR2 1 C/T2# 0 CP/RL2# Bit Mnemonic Description Timer 2 Overflow Flag TF2 is not set if RCLK=1 or TCLK = 1. Must be cleared by software. Set by hardware on Timer 2 overflow. Timer 2 External Flag Set when a capture or a reload is caused by a negative transition on T2EX pin if EXEN2=1. Set to cause the CPU to vector to Timer 2 interrupt routine when Timer 2 interrupt is enabled. Must be cleared by software. Receive Clock bit Clear to use timer 1 overflow as receive clock for serial port in mode 1 or 3. Set to use Timer 2 overflow as receive clock for serial port in mode 1 or 3. Transmit Clock bit Clear to use timer 1 overflow as transmit clock for serial port in mode 1 or 3. Set to use Timer 2 overflow as transmit clock for serial port in mode 1 or 3. Timer 2 External Enable bit Clear to ignore events on T2EX pin for Timer 2 operation. Set to cause a capture or reload when a negative transition on T2EX pin is detected, if Timer 2 is not used to clock the serial port. Timer 2 Run Control bit Clear to turn off Timer 2. Set to turn on Timer 2. Timer/Counter 2 Select bit Clear for timer operation (input from internal clock system: fOSC). Set for counter operation (input from T2 input pin). Timer 2 Capture/Reload bit If RCLK=1 or TCLK=1, CP/RL2# is ignored and timer is forced to auto-reload on Timer 2 overflow. Clear to auto-reload on Timer 2 overflows or negative transitions on T2EX pin if EXEN2=1. Set to capture on negative transitions on T2EX pin if EXEN2=1. 7 TF2 6 EXF2 5 RCLK 4 TCLK 3 EXEN2 2 TR2 1 C/T2# 0 CP/RL2# Reset Value = 0000 0000b bit addressable 64 AT89C5115 4128F-8051-05/06 AT89C5115 Table 44. T2MOD Register T2MOD (S:C9h) Timer 2 Mode Control Register 7 Bit Number 7 6 5 4 3 2 1 T2OE 0 DCEN Bit Mnemonic Description Reserved The value read from this bit is indeterminate. Do not set this bit. Reserved The value read from this bit is indeterminate. Do not set this bit. Reserved The value read from this bit is indeterminate. Do not set this bit. Reserved The value read from this bit is indeterminate. Do not set this bit. Reserved The value read from this bit is indeterminate. Do not set this bit. Reserved The value read from this bit is indeterminate. Do not set this bit. Timer 2 Output Enable bit Clear to program P1.0/T2 as clock input or I/O port. Set to program P1.0/T2 as clock output. Down Counter Enable bit Clear to disable Timer 2 as up/down counter. Set to enable Timer 2 as up/down counter. 6 - 5 - 4 - 3 - 2 - 1 T2OE 0 DCEN Reset Value = XXXX XX00b Not bit addressable Table 45. TH2 Register TH2 (S:CDh) Timer 2 High Byte Register 7 Bit Number 7-0 6 5 4 3 2 1 0 - Bit Mnemonic Description High Byte of Timer 2 Reset Value = 0000 0000b Not bit addressable 65 4128F-8051-05/06 Table 46. TL2 Register TL2 (S:CCh) Timer 2 Low Byte Register 7 Bit Number 7-0 6 5 4 3 2 1 0 - Bit Mnemonic Description Low Byte of Timer 2 Reset Value = 0000 0000b Not bit addressable Table 47. RCAP2H Register RCAP2H (S:CBh) Timer 2 Reload/Capture High Byte Register 7 Bit Number 7-0 6 5 4 3 2 1 0 - Bit Mnemonic Description High Byte of Timer 2 Reload/Capture. Reset Value = 0000 0000b Not bit addressable Table 48. RCAP2L Register RCAP2L (S:CAh) Timer 2 Reload/Capture Low Byte Register 7 Bit Number 7-0 6 5 4 3 2 1 0 - Bit Mnemonic Description Low Byte of Timer 2 Reload/Capture. Reset Value = 0000 0000b Not bit addressable 66 AT89C5115 4128F-8051-05/06 AT89C5115 Watchdog Timer T89C5115 contains a powerful programmable hardware Watchdog Timer (WDT) that automatically resets the chip if it software fails to reset the WDT before the selected time interval has elapsed. It permits large Timeout ranging from 16ms to 2s @fOSC = 12 MHz in X1 mode. This WDT consists of a 14-bit counter plus a 7-bit programmable counter, a Watchdog Timer reset register (WDTRST) and a Watchdog Timer programming (WDTPRG) register. When exiting reset, the WDT is -by default- disable. To enable the WDT, the user has to write the sequence 1EH and E1H into WDTRST register with no instruction between the two writes. When the Watchdog Timer is enabled, it will increment every machine cycle while the oscillator is running and there is no way to disable the WDT except through reset (either hardware reset or WDT overflow reset). When WDT overflows, it will generate an output RESET pulse at the RST pin. The RESET pulse duration is 96xTOSC, where TOSC=1/fOSC. To make the best use of the WDT, it should be serviced in those sections of code that will periodically be executed within the time required to prevent a WDT reset Note: When the watchdog is enable it is impossible to change its period. Figure 31. Watchdog Timer RESET WR Decoder Control WDTRST Enable 14-bit Counter Fwd Clock WDTPRG 7-bit Counter Outputs 4128F-8051-05/06 0 1 2 - - - - - RESET 67 Watchdog Programming The three lower bits (S0, S1, S2) located into WDTPRG register permit to program the WDT duration. Table 49. Machine Cycle Count S2 0 0 0 0 1 1 1 1 S1 0 0 1 1 0 0 1 1 S0 0 1 0 1 0 1 0 1 Machine Cycle Count 214 - 1 215 - 1 216 - 1 217 - 1 218 - 1 219 - 1 220 - 1 221 - 1 To compute WD Timeout, the following formula is applied: Note: Svalue represents the decimal value of (S2 S1 S0) Find Hereafter computed Timeout values for fOSCXTAL = 12 MHz in X1 mode Table 50. Timeout Computation S2 0 0 0 0 1 1 1 1 S1 0 0 1 1 0 0 1 1 S0 0 1 0 1 0 1 0 1 fOSC=12 MHz 16.38 ms 32.77 ms 65.54 ms 131.07 ms 262.14 ms 524.29 ms 1.05 s 2.10 s fOSC=16MHz 12.28 ms 24.57 ms 49.14 ms 98.28 ms 196.56 ms 393.12 ms 786.24 ms 1.57 s fOSC =20 MHz 9.82 ms 19.66 ms 39.32 ms 78.64 ms 157.28 ms 314.56 ms 629.12 ms 1.25 s 68 AT89C5115 4128F-8051-05/06 - -------------------------------------------------------------------------- 6x2 (2 x2 eu l avS 2 2 X c so F XD W = tu O em i T F - 14 ) AT89C5115 Watchdog Timer During Power-down Mode and Idle In Power-down mode the oscillator stops, which means the WDT also stops. While in Power-down mode, the user does not need to service the WDT. There are 2 methods of exiting Power-down mode: by a hardware reset or via a level activated external interrupt which is enabled prior to entering Power-down mode. When Power-down is exited with hardware reset, the watchdog is disabled. Exiting Power-down with an interrupt is significantly different. The interrupt shall be held low long enough for the oscillator to stabilize. When the interrupt is brought high, the interrupt is serviced. To prevent the WDT from resetting the device while the interrupt pin is held low, the WDT is not started until the interrupt is pulled high. It is suggested that the WDT be reset during the interrupt service for the interrupt used to exit Power-down. To ensure that the WDT does not overflow within a few states of exiting powerdown, it is best to reset the WDT just before entering powerdown. In the Idle mode, the oscillator continues to run. To prevent the WDT from resetting T89C5115 while in Idle mode, the user should always set up a timer that will periodically exit Idle, service the WDT, and re-enter Idle mode. Register Table 51. WDTPRG Register WDTPRG (S:A7h) - Watchdog Timer Duration Programming register 7 Bit Number 7 6 5 4 3 2 1 0 6 5 4 3 2 S2 1 S1 0 S0 Bit Mnemonic Description S2 S1 S0 Reserved The value read from this bit is indeterminate. Do not set this bit. Reserved The value read from this bit is indeterminate. Do not set this bit. Reserved The value read from this bit is indeterminate. Do not set this bit. Reserved The value read from this bit is indeterminate. Do not set this bit. Reserved The value read from this bit is indeterminate. Do not set this bit. Watchdog Timer Duration selection bit 2 Work in conjunction with bit 1 and bit 0. Watchdog Timer Duration selection bit 1 Work in conjunction with bit 2 and bit 0. Watchdog Timer Duration selection bit 0 Work in conjunction with bit 1 and bit 2. Reset Value = XXXX X000b 69 4128F-8051-05/06 Table 52. WDTRST Register WDTRST (S:A6h Write Only) - Watchdog Timer Enable register 7 Bit Number 7 6 5 4 3 2 1 0 - Bit Mnemonic Description Watchdog Control Value Reset Value = 1111 1111b Note: The WDRST register is used to reset/enable the WDT by writing 1EH then E1H in sequence without instruction between these two sequences. 70 AT89C5115 4128F-8051-05/06 AT89C5115 Programmable Counter Array (PCA) The PCA provides more timing capabilities with less CPU intervention than the standard timer/counters. Its advantages include reduced software overhead and improved accuracy. The PCA consists of a dedicated timer/counter which serves as the time base for an array of two compare/capture modules. Its clock input can be programmed to count any of the following signals: * * * * * * * * PCA clock frequency/6 (See "clock" section) PCA clock frequency/2 Timer 0 overflow External input on ECI (P1.2) Rising and/or falling edge capture, Software timer High-speed output Pulse width modulator Each compare/capture modules can be programmed in any one of the following modes: When the compare/capture modules are programmed in capture mode, software timer, or high speed output mode, an interrupt can be generated when the module executes its function. Both modules and the PCA timer overflow share one interrupt vector. The PCA timer/counter and compare/capture modules share Port 1 for external I/Os. These pins are listed below. If the port is not used for the PCA, it can still be used for standard I/O. PCA Component 16-bit Counter 16-bit Module 0 16-bit Module 1 External I/O Pin P1.2/ECI P1.3/CEX0 P1.4/CEX1 PCA Timer The PCA timer is a common time base for both modules (See Figure 9). The timer count source is determined from the CPS1 and CPS0 bits in the CMOD SFR (See Table 8) and can be programmed to run at: * * * * 1/6 the PCA clock frequency. 1/2 the PCA clock frequency. The Timer 0 overflow. The input on the ECI pin (P1.2). 71 4128F-8051-05/06 Figure 32. PCA Timer/Counter To PCA modules FPca/6 FPca/2 T0 OVF P1.2 CH CL 16-bit up counter overflow It CIDL Idle CPS1 CPS0 ECF CMOD 0xD9 CF CR CCF1 CCF0 CCON 0xD8 The CMOD register includes three additional bits associated with the PCA. * * The CIDL bit which allows the PCA to stop during idle mode. The ECF bit which when set causes an interrupt and the PCA overflow flag CF in CCON register to be set when the PCA timer overflows. The CCON register contains the run control bit for the PCA and the flags for the PCA timer and each module. * * * The CR bit must be set to run the PCA. The PCA is shut off by clearing this bit. The CF bit is set when the PCA counter overflows and an interrupt will be generated if the ECF bit in CMOD register is set. The CF bit can only be cleared by software. The CCF0:1 bits are the flags for the modules (CCF0 for module0...) and are set by hardware when either a match or a capture occurs. These flags also can be cleared by software. 72 AT89C5115 4128F-8051-05/06 AT89C5115 PCA Modules Each one of the two compare/capture modules has six possible functions. It can perform: * * * * * * 16-bit Capture, positive-edge triggered 16-bit Capture, negative-edge triggered 16-bit Capture, both positive and negative-edge triggered 16-bit Software Timer 16-bit High Speed Output 8-bit Pulse Width Modulator. Each module in the PCA has a special function register associated with it (CCAPM0 for module 0 ...). The CCAPM0:1 registers contain the bits that control the mode that each module will operate in. * * * The ECCF bit enables the CCF flag in the CCON register to generate an interrupt when a match or compare occurs in the associated module. The PWM bit enables the pulse width modulation mode. The TOG bit when set causes the CEX output associated with the module to toggle when there is a match between the PCA counter and the module's capture/compare register. The match bit MAT when set will cause the CCFn bit in the CCON register to be set when there is a match between the PCA counter and the module's capture/compare register. The two bits CAPN and CAPP in CCAPMn register determine the edge that a capture input will be active on. The CAPN bit enables the negative edge, and the CAPP bit enables the positive edge. If both bits are set both edges will be enabled. The bit ECOM in CCAPM register when set enables the comparator function. * * * 73 4128F-8051-05/06 PCA Interrupt Figure 33. PCA Interrupt System CF PCA Timer/Counter CR CCF1 CCF0 CCON 0xD8 Module 0 Module 1 To Interrupt ECF CMOD.0 ECCFn CCAPMn.0 EC IEN0.6 EA IEN0.7 PCA Capture Mode To use one of the PCA modules in capture mode either one or both of the CCAPM bits CAPN and CAPP for that module must be set. The external CEX input for the module (on port 1) is sampled for a transition. When a valid transition occurs the PCA hardware loads the value of the PCA counter registers (CH and CL) into the module's capture registers (CCAPnL and CCAPnH). If the CCFn bit for the module in the CCON SFR and the ECCFn bit in the CCAPMn SFR are set then an interrupt will be generated. Figure 34. PCA Capture Mode PCA Counter CH (8-bits) CL (8-bits) CEXn n = 0, 1 CCAPnH CCAPnL CCFn CCON Reg 7 PCA Interrupt Request 0CAPPnCAPNn000ECCFn 0 CCAPMn Register (n = 0, 1) 74 AT89C5115 4128F-8051-05/06 AT89C5115 16-bit Software Timer Mode The PCA modules can be used as software timers by setting both the ECOM and MAT bits in the modules CCAPMn register. The PCA timer will be compared to the module's capture registers and when a match occurs an interrupt will occur if the CCFn (CCON SFR) and the ECCFn (CCAPMn SFR) bits for the module are both set. Figure 35. PCA 16-bit Software Timer and High Speed Output Mode PCA Counter CH CL (8 bits) (8 bits) Compare/Capture Module CCAPnL CCAPnH (8 bits) (8 bits) Match 16-bit Comparator Enable CCFn CCON reg Toggle CEXn PCA Interrupt Request ECOMn0 0 MATn TOGn0 ECCFn 0 CCAPMn Register (n = 0, 1) For software Timer mode, set ECOMn and MATn. For high speed output mode, set ECOMn, MATn and TOGn. 7 "0" Reset Write to CCAPnL Write to CCAPnH "1" 4128F-8051-05/06 - 75 High Speed Output Mode In this mode the CEX output (on port 1) associated with the PCA module will toggle each time a match occurs between the PCA counter and the module's capture registers. To activate this mode the TOG, MAT, and ECOM bits in the module's CCAPMn SFR must be set. Figure 36. PCA High Speed Output Mode CCON CF Write to CCAPnH Write to CCAPnL "0" "1" Reset PCA IT CCAPnH Enable 16 bit comparator CCAPnL Match CR CCF1 CCF0 0xD8 CH CL CEXn PCA counter/timer CCAPMn, n = 0 to 1 0xDA to 0xDE ECOMn CAPPn CAPNn MATn TOGn PWMn ECCFn Pulse Width Modulator Mode All the PCA modules can be used as PWM outputs. The output frequency depends on the source for the PCA timer. All the modules will have the same output frequency because they all share the PCA timer. The duty cycle of each module is independently variable using the module's capture register CCAPLn. When the value of the PCA CL SFR is less than the value in the module's CCAPLn SFR the output will be low, when it is equal to or greater than it, the output will be high. When CL overflows from FF to 00, CCAPLn is reloaded with the value in CCAPHn. the allows the PWM to be updated without glitches. The PWM and ECOM bits in the module's CCAPMn register must be set to enable the PWM mode. 76 AT89C5115 4128F-8051-05/06 AT89C5115 Figure 37. PCA PWM Mode CCAPnH CL rolls over from FFh TO 00h loads CCAPnH contents into CCAPnL CCAPnL "0" CL < CCAPnL CL (8 bits) 8-bit Comparator CEX CL >= CCAPnL "1" ECOMn CCAPMn.6 PWMn CCAPMn.1 77 4128F-8051-05/06 PCA Registers Table 53. CMOD Register CMOD (S:D9h) PCA Counter Mode Register 7 CIDL 6 Bit Mnemonic 5 4 3 2 CPS1 1 CPS0 0 ECF Bit Number Description PCA Counter Idle Control bit Clear to let the PCA run during Idle mode. Set to stop the PCA when Idle mode is invoked. Reserved The value read from this bit is indeterminate. Do not set this bit. Reserved The value read from this bit is indeterminate. Do not set this bit. Reserved The value read from this bit is indeterminate. Do not set this bit. Reserved The value read from this bit is indeterminate. Do not set this bit. EWC Count Pulse Select bits CPS1 CPS0 Clock source 0 0 Internal Clock, FPca/6 0 1 Internal Clock, FPca/2 1 0 Timer 0 overflow 1 1 External clock at ECI/P1.2 pin (Max. Rate = FPca/4) Enable PCA Counter Overflow Interrupt bit Clear to disable CF bit in CCON register to generate an interrupt. Set to enable CF bit in CCON register to generate an interrupt. 7 CIDL 6 - 5 - 4 - 3 - 2-1 CPS1:0 0 ECF Reset Value = 0XXX X000b 78 AT89C5115 4128F-8051-05/06 AT89C5115 Table 54. CCON Register CCON (S:D8h) PCA Counter Control Register 7 CF Bit Number 6 CR 5 Bit Mnemonic 4 Description PCA Timer/Counter Overflow flag Set by hardware when the PCA Timer/Counter rolls over. This generates a PCA interrupt request if the ECF bit in CMOD register is set. Must be cleared by software. PCA Timer/Counter Run Control bit Clear to turn the PCA Timer/Counter off. Set to turn the PCA Timer/Counter on. Reserved The value read from these bist are indeterminate. Do not set these bits. PCA Module 1 Compare/Capture Flag Set by hardware when a match or capture occurs. This generates a PCA interrupt request if the ECCF 1 bit in CCAPM 1 register is set. Must be cleared by software. PCA Module 0 Compare/Capture Flag Set by hardware when a match or capture occurs. This generates a PCA interrupt request if the ECCF 0 bit in CCAPM 0 register is set. Must be cleared by software. 3 2 1 CCF1 0 CCF0 7 CF 6 CR 5-2 - 1 CCF1 0 CCF0 Reset Value = 00xx xx00b 79 4128F-8051-05/06 Table 55. CCAPnH Registers CCAP0H (S:FAh) CCAP1H (S:FBh) PCA High Byte Compare/Capture Module n Register (n=0..1) 7 CCAPnH 7 6 CCAPnH 6 5 CCAPnH 5 4 CCAPnH 4 Description High byte of EWC-PCA comparison or capture values 3 CCAPnH 3 2 CCAPnH 2 1 CCAPnH 1 0 CCAPnH 0 Bit Number 7:0 Bit Mnemonic CCAPnH 7:0 Reset Value = 0000 0000b Table 56. CCAPnL Registers CCAP0L (S:EAh) CCAP1L (S:EBh) PCA Low Byte Compare/Capture Module n Register (n=0..1) 7 CCAPnL 7 6 CCAPnL 6 5 CCAPnL 5 4 CCAPnL 4 Description Low byte of EWC-PCA comparison or capture values 3 CCAPnL 3 2 CCAPnL 2 1 CCAPnL 1 0 CCAPnL 0 Bit Number 7:0 Bit Mnemonic CCAPnL 7:0 Reset Value = 0000 0000b 80 AT89C5115 4128F-8051-05/06 AT89C5115 Table 57. CCAPMn Registers CCAPM0 (S:DAh) CCAPM1 (S:DBh) PCA Compare/Capture Module n Mode registers (n=0..1) 7 Bit Number 7 6 ECOMn 5 CAPPn 4 CAPNn Description Reserved The Value read from this bit is indeterminate. Do not set this bit. Enable Compare Mode Module x bit Clear to disable the Compare function. Set to enable the Compare function. The Compare function is used to implement the software Timer, the high-speed output, the Pulse Width Modulator (PWM) and the Watchdog Timer (WDT). Capture Mode (Positive) Module x bit Clear to disable the Capture function triggered by a positive edge on CEXx pin. Set to enable the Capture function triggered by a positive edge on CEXx pin Capture Mode (Negative) Module x bit Clear to disable the Capture function triggered by a negative edge on CEXx pin. Set to enable the Capture function triggered by a negative edge on CEXx pin. Match Module x bit Set when a match of the PCA Counter with the Compare/Capture register sets CCFx bit in CCON register, flagging an interrupt. Toggle Module x bit The toggle mode is configured by setting ECOMx, MATx and TOGx bits. Set when a match of the PCA Counter with the Compare/Capture register toggles the CEXx pin. Pulse Width Modulation Module x Mode bit Set to configure the module x as an 8-bit Pulse Width Modulator with output waveform on CEXx pin. Enable CCFx Interrupt bit Clear to disable CCFx bit in CCON register to generate an interrupt request. Set to enable CCFx bit in CCON register to generate an interrupt request. 3 MATn 2 TOGn 1 PWMn 0 ECCFn Bit Mnemonic - 6 ECOMn 5 CAPPn 4 CAPNn 3 MATn 2 TOGn 1 PWMn 0 ECCFn Reset Value = X000 0000b 81 4128F-8051-05/06 Table 58. CH Register CH (S:F9h) PCA Counter Register High value 7 CH 7 Bit Number 7:0 6 CH 6 5 CH 5 Bit Mnemonic CH 7:0 4 CH 4 Description High byte of Timer/Counter 3 CH 3 2 CH 2 1 CH 1 0 CH 0 Reset Value = 0000 00000b Table 59. CL Register CL (S:E9h) PCA counter Register Low value 7 CL 7 Bit Number 7:0 6 CL 6 5 CL 5 Bit Mnemonic CL0 7:0 4 CL 4 Description Low byte of Timer/Counter 3 CL 3 2 CL 2 1 CL 1 0 CL 0 Reset Value = 0000 00000b 82 AT89C5115 4128F-8051-05/06 AT89C5115 Analog-to-Digital Converter (ADC) This section describes the on-chip 10-bit analog-to-digital converter of the T89C5115. Eight ADC channels are available for sampling of the external sources AN0 to AN7. An analog multiplexer allows the single ADC converter to select one from the 8 ADC channels as ADC input voltage (ADCIN). ADCIN is converted by the 10-bit-cascaded potentiometric ADC. Two modes of conversion are available: - Standard conversion (8 bits). - Precision conversion (10 bits). For the precision conversion, set bit PSIDLE in ADCON register and start conversion. The device is in a pseudo-idle mode, the CPU does not run but the peripherals are always running. This mode allows digital noise to be as low as possible, to ensure high precision conversion. For this mode it is necessary to work with end of conversion interrupt, which is the only way to wake the device up. If another interrupt occurs during the precision conversion, it will be served only after this conversion is completed. Features * * * * * * * * * * 8 channels with multiplexed inputs 10-bit cascaded potentiometric ADC Conversion time 16 micro-seconds (typ.) Zero Error (offset) 2 LSB max Positive External Reference Voltage Range (VAREF) 2.4 to 3.0-volt (typ.) ADCIN Range 0 to 3-volt Integral non-linearity typical 1 LSB, max. 2 LSB Differential non-linearity typical 0.5 LSB, max. 1 LSB Conversion Complete Flag or Conversion Complete Interrupt Selectable ADC Clock ADC Port1 I/O Functions Port 1 pins are general I/O that are shared with the ADC channels. The channel select bit in ADCF register define which ADC channel/port1 pin will be used as ADCIN. The remaining ADC channels/port1 pins can be used as general purpose I/O or as the alternate function that is available. A conversion launched on a channel which are not selected on ADCF register will not have any effect. VAREF VAREF should be connected to a low impedance point and must remain in the range specified VAREF absolute maximum range (See section "AC-DC"). . If the ADC is not used, it is recommended to tie VAREF to VAGND. 83 4128F-8051-05/06 Figure 38. ADC Description ADCON.5 ADCON.3 ADEN ADSST ADCON.4 ADC CLOCK ADEOC CONTROL ADC Interrupt Request EADC IEN1.1 AN0/P1.0 AN1/P1.1 AN2/P1.2 AN3/P1.3 AN4/P1.4 AN5/P1.5 AN6/P1.6 AN7/P1.7 000 001 010 011 100 101 110 111 Cai Rai ADCIN 8 + SAR 2 ADDH ADDL AVSS Sample and Hold R/2R DAC 10 SCH2 ADCON.2 SCH1 ADCON.1 SCH0 ADCON.0 VAREF VAGND Figure 39 shows the timing diagram of a complete conversion. For simplicity, the figure depicts the waveforms in idealized form and do not provide precise timing information. For ADC characteristics and timing parameters refer to the section "AC Characteristics" of this datasheet. Figure 39. Timing Diagram CLK ADEN TSETUP ADSST TCONV ADEOC Note: Tsetup min, see the AC Parameter for A/D conversion. Tconv = 11 clock ADC = 1sample and hold + 10-bit conversion The user must ensure that Tsetup time between setting ADEN and the start of the first conversion. ADC Converter Operation A start of single A/D conversion is triggered by setting bit ADSST (ADCON.3). After completion of the A/D conversion, the ADSST bit is cleared by hardware. The end-of-conversion flag ADEOC (ADCON.4) is set when the value of conversion is available in ADDH and ADDL, it must be cleared by software. If the bit EADC (IEN1.1) is set, an interrupt occur when flag ADEOC is set (See Figure 41). Clear this flag for rearming the interrupt. Note: Always leave Tsetup time before starting a conversion unless ADEN is permanently high. In this case one should wait Tsetup only before the first conversion 84 AT89C5115 4128F-8051-05/06 AT89C5115 The bits SCH0 to SCH2 in ADCON register are used for the analog input channel selection. Table 60. Selected Analog input SCH2 0 0 0 0 1 1 1 1 SCH1 0 0 1 1 0 0 1 1 SCH0 0 1 0 1 0 1 0 1 Selected Analog Input AN0 AN1 AN2 AN3 AN4 AN5 AN6 AN7 Voltage Conversion When the ADCIN is equals to VAREF the ADC converts the signal to 3FFh (full scale). If the input voltage equals VAGND, the ADC converts it to 000h. Input voltage between VAREF and VAGND are a straight-line linear conversion. All other voltages will result in 3FFh if greater than VAREF and 000h if less than VAGND. Note that ADCIN should not exceed VAREF absolute maximum range (See section "AC-DC"). Clock Selection The ADC clock is the same as CPU. The maximum clock frequency is defined in the DC parmeter for A/D converter. A prescaler is featured (ADCCLK) to generate the ADC clock from the oscillator frequency. if PRS = 0 then FADC = Fperiph / 64 if PRS > 0 then FADC = Fperiph / 2 x PRS Figure 40. A/D Converter Clock CPU CLOCK /2 Prescaler ADCLK ADC Clock A/D Converter CPU Core Clock Symbol ADC Standby Mode IT ADC management When the ADC is not used, it is possible to set it in standby mode by clearing bit ADEN in ADCON register. In this mode the power dissipation is reduced. An interrupt end-of-conversion will occurs when the bit ADEOC is activated and the bit EADC is set. For re-arming the interrupt the bit ADEOC must be cleared by software. 85 4128F-8051-05/06 Figure 41. ADC interrupt structure ADEOC ADCON.2 ADCI EADC IEN1.1 Routine Examples 1. Configure P1.2 and P1.3 in ADC channels // configure channel P1.2 and P1.3 for ADC ADCF = 0Ch // Enable the ADC ADCON = 20h 2. Start a standard conversion // The variable 'channel' contains the channel to convert // The variable 'value_converted' is an unsigned int // Clear the field SCH[2:0] ADCON &= F8h // Select channel ADCON |= channel // Start conversion in standard mode ADCON |= 08h // Wait flag End of conversion while((ADCON & 01h)!= 01h) // Clear the End of conversion flag ADCON &= EFh // read the value value_converted = (ADDH << 2)+(ADDL) 3. Start a precision conversion (need interrupt ADC) // The variable 'channel' contains the channel to convert // Enable ADC EADC = 1 // clear the field SCH[2:0] ADCON &= F8h // Select the channel ADCON |= channel // Start conversion in precision mode ADCON |= 48h Note: To enable the ADC interrupt: EA = 1 86 AT89C5115 4128F-8051-05/06 AT89C5115 Registers Table 61. ADCF Register ADCF (S:F6h) ADC Configuration 7 CH 7 Bit Number 6 CH 6 5 CH 5 4 CH 4 3 CH 3 2 CH 2 1 CH 1 0 CH 0 Bit Mnemonic Description Channel Configuration Set to use P1.x as ADC input. Clear to use P1.x as standart I/O port. 7-0 CH 0:7 Reset Value = 0000 0000b Table 62. ADCON Register ADCON (S:F3h) ADC Control Register 7 Bit Number 7 6 PSIDLE 5 ADEN 4 ADEOC 3 ADSST 2 SCH2 1 SCH1 0 SCH0 Bit Mnemonic Description Reserved The value read from these bits are indeterminate. Do not set these bits. Pseudo Idle Mode (Best Precision) Set to put in idle mode during conversion Clear to convert without idle mode. Enable/Standby Mode Set to enable ADC Clear for Standby mode. End Of Conversion Set by hardware when ADC result is ready to be read. This flag can generate an interrupt. Must be cleared by software. Start and Status Set to start an A/D conversion. Cleared by hardware after completion of the conversion Selection of Channel to Convert See Table 60 6 PSIDLE 5 ADEN 4 ADEOC 3 ADSST 2-0 SCH2:0 Reset Value = X000 0000b 87 4128F-8051-05/06 Table 63. ADCLK Register ADCLK (S:F2h) ADC Clock Prescaler 7 Bit Number 7-5 6 5 4 PRS 4 3 PRS 3 2 PRS 2 1 PRS 1 0 PRS 0 Bit Mnemonic Description Reserved The value read from these bits are indeterminate. Do not set these bits. Clock Prescaler Fadc = Fcpuclock/(4*PRS)) in X1 mode Fadc=Fcpuclock/(2*PRS) in X2 mode 4-0 PRS4:0 Reset Value = XXX0 0000b Table 64. ADDH Register ADDH (S:F5h Read Only) ADC Data High Byte Register 7 ADAT 9 Bit Number 7-0 6 ADAT 8 5 ADAT 7 4 ADAT 6 3 ADAT 5 2 ADAT 4 1 ADAT 3 0 ADAT 2 Bit Mnemonic Description ADAT9:2 ADC result bits 9-2 Reset Value = 00h Table 65. ADDL Register ADDL (S:F4h Read Only) ADC Data Low Byte Register 7 Bit Number 7-2 6 5 4 3 2 1 ADAT 1 0 ADAT 0 Bit Mnemonic Description Reserved The value read from these bits are indeterminate. Do not set these bits. ADC result bits 1-0 1-0 ADAT1:0 Reset Value = 00h 88 AT89C5115 4128F-8051-05/06 AT89C5115 Interrupt System Introduction The T89C5115 has a total of 8 interrupt vectors: two external interrupts (INT0 and INT1), three timer interrupts (timers 0, 1 and 2), a serial port interrupt, a PCAand an ADC. These interrupts are shown below. Figure 42. Interrupt Control System INT0# External Interrupt 0 EX0 IEN0.0 00 01 10 11 00 01 10 11 00 01 10 11 00 01 10 11 00 01 10 11 00 01 10 11 Highest Priority Interrupts Timer 0 ET0 IEN0.1 INT1# External Interrupt 1 EX1 IEN0.2 Timer 1 ET1 CEX0:1 IEN0.3 PCA EC TxD RxD ES IEN0.4 UART IEN0.6 Timer 2 ET2 IEN0.5 00 01 10 11 AIN1:0 ADC EADC IEN1.1 00 01 10 11 EA IEN0.7 IPH/L Interrupt Enable Priority Enable Lowest Priority Interrupts 89 4128F-8051-05/06 Each of the interrupt sources can be individually enabled or disabled by setting or clearing a bit in the Interrupt Enable register. This register also contains a global disable bit which must be cleared to disable all the interrupts at the same time. Each interrupt source can also be individually programmed to one of four priority levels by setting or clearing a bit in the Interrupt Priority registers. The Table below shows the bit values and priority levels associated with each combination. Table 66. Priority Level bit Values IPH.x 0 0 1 1 IPL.x 0 1 0 1 Interrupt Level Priority 0 (Lowest) 1 2 3 (Highest) A low-priority interrupt can be interrupted by a high priority interrupt but not by another low-priority interrupt. A high-priority interrupt cannot be interrupted by any other interrupt source. If two interrupt requests of different priority levels are received simultaneously, the request of the higher priority level is serviced. If interrupt requests of the same priority level are received simultaneously, an internal polling sequence determines which request is serviced. Thus within each priority level there is a second priority structure determined by the polling sequence, See Table 67. Table 67. Interrupt Priority Within Level Interrupt Name External interrupt (INT0) Timer0 (TF0) External interrupt (INT1) Timer 1 (TF1) PCA (CF or CCFn) UART (RI or TI) Timer 2 (TF2) ADC (ADCI) Interrupt Address Vector 0003h 000Bh 0013h 001Bh 0033h 0023h 002Bh 0043h Priority Number 1 2 3 4 5 6 7 9 90 AT89C5115 4128F-8051-05/06 AT89C5115 Registers Figure 43. IEN0 Register IEN0 (S:A8h) Interrupt Enable Register 7 EA Bit Number 6 EC 5 ET2 4 ES 3 ET1 2 EX1 1 ET0 0 EX0 Bit Mnemonic Description Enable All Interrupt bit Clear to disable all interrupts. Set to enable all interrupts. If EA=1, each interrupt source is individually enabled or disabled by setting or clearing its interrupt enable bit. PCA Interrupt Enable Clear to disable the PCA interrupt. Set to enable the PCA interrupt. Timer 2 Overflow Interrupt Enable bit Clear to disable Timer 2 overflow interrupt. Set to enable Timer 2 overflow interrupt. Serial port Enable bit Clear to disable serial port interrupt. Set to enable serial port interrupt. Timer 1 Overflow Interrupt Enable bit Clear to disable timer 1 overflow interrupt. Set to enable timer 1 overflow interrupt. External Interrupt 1 Enable bit Clear to disable external interrupt 1. Set to enable external interrupt 1. Timer 0 Overflow Interrupt Enable bit Clear to disable timer 0 overflow interrupt. Set to enable timer 0 overflow interrupt. External Interrupt 0 Enable bit Clear to disable external interrupt 0. Set to enable external interrupt 0. 7 EA 6 EC 5 ET2 4 ES 3 ET1 2 EX1 1 ET0 0 EX0 Reset Value = 0000 0000b bit addressable 91 4128F-8051-05/06 Figure 44. IEN1 Register IEN1 (S:E8h) Interrupt Enable Register 7 Bit Number 7 6 5 4 3 2 1 EADC 0 - Bit Mnemonic Description Reserved The value read from this bit is indeterminate. Do not set this bit. Reserved The value read from this bit is indeterminate. Do not set this bit. Reserved The value read from this bit is indeterminate. Do not set this bit. Reserved The value read from this bit is indeterminate. Do not set this bit. Reserved The value read from this bit is indeterminate. Do not set this bit. Reserved The value read from this bit is indeterminate. Do not set this bit. ADC Interrupt Enable bit Clear to disable the ADC interrupt. Set to enable the ADC interrupt. Reserved The value read from this bit is indeterminate. Do not set this bit. 6 - 5 - 4 - 3 - 2 - 1 EADC 0 - Reset Value = xxxx x000b bit addressable 92 AT89C5115 4128F-8051-05/06 AT89C5115 Table 68. IPL0 Register IPL0 (S:B8h) Interrupt Enable Register 7 Bit Number 7 6 PPC 5 PT2 4 PS 3 PT1 2 1 PT0 0 - Bit Mnemonic Description Reserved The value read from this bit is indeterminate. Do not set this bit. PCA Interrupt Priority bit Refer to PPCH for priority level Timer 2 Overflow Interrupt Priority bit Refer to PT2H for priority level. Serial Port Priority bit Refer to PSH for priority level. Timer 1 Overflow Interrupt Priority bit Refer to PT1H for priority level. External Interrupt 1 Priority bit Refer to PX1H for priority level. Timer 0 Overflow Interrupt Priority bit Refer to PT0H for priority level. External Interrupt 0 Priority bit Refer to PX0H for priority level. 6 PPC 5 PT2 4 PS 3 PT1 2 PX1 1 PT0 0 PX0 Reset Value = X000 0000b bit addressable 93 4128F-8051-05/06 Table 69. IPL1 Register IPL1 (S:F8h) Interrupt Priority Low Register 1 7 Bit Number 7 6 5 4 3 2 POVRL 1 PADCL 0 - Bit Mnemonic Description Reserved The value read from this bit is indeterminate. Do not set this bit. Reserved The value read from this bit is indeterminate. Do not set this bit. Reserved The value read from this bit is indeterminate. Do not set this bit. Reserved The value read from this bit is indeterminate. Do not set this bit. Reserved The value read from this bit is indeterminate. Do not set this bit. Timer Overrun Interrupt Priority Level Less Significant bit Refer to PI2CH for priority level. ADC Interrupt Priority Level Less Significant bit Refer to PSPIH for priority level. Reserved The value read from this bit is indeterminate. Do not set this bit. 6 - 5 - 4 - 3 - 2 POVRL 1 PADCL 0 - Reset Value = XXXX X000b bit addressable 94 AT89C5115 4128F-8051-05/06 AT89C5115 Table 70. IPH0 Register IPH0 (B7h) Interrupt High Priority Register 7 Bit Number 7 6 PPCH 5 PT2H 4 PSH 3 PT1H 2 PX1H 1 PT0H 0 PX0H Bit Mnemonic Description Reserved The value read from this bit is indeterminate. Do not set this bit. PCA Interrupt Priority Level Most Significant bit PPCH PPC Priority level 0 0 Lowest 0 1 1 0 1 1 Highest priority Timer 2 Overflow Interrupt High Priority bit PT2H PT2 Priority Level 0 0 Lowest 0 1 1 0 1 1 Highest Serial Port High Priority bit PSH PS Priority Level 0 0 Lowest 0 1 1 0 1 1 Highest Timer 1 Overflow Interrupt High Priority bit PT1H PT1 Priority Level 0 0 Lowest 0 1 1 0 1 1 Highest External Interrupt 1 High Priority bit PX1H PX1 Priority Level 0 0 Lowest 0 1 1 0 1 1 Highest Timer 0 Overflow Interrupt High Priority bit PT0H PT0 Priority Level 0 0 Lowest 0 1 1 0 1 1 Highest External Interrupt 0 High Priority bit PX0H PX0 Priority Level 0 0 Lowest 0 1 1 0 1 1 Highest 6 PPCH 5 PT2H 4 PSH 3 PT1H 2 PX1H 1 PT0H 0 PX0H Reset Value = X000 0000b 95 4128F-8051-05/06 Table 71. IPH1 Register IPH1 (S:F7h) Interrupt high priority Register 1 7 Bit Number 7 6 5 4 3 2 POVRH 1 PADCH 0 - Bit Mnemonic Description Reserved The value read from this bit is indeterminate. Do not set this bit. Reserved The value read from this bit is indeterminate. Do not set this bit. Reserved The value read from this bit is indeterminate. Do not set this bit. Reserved The value read from this bit is indeterminate. Do not set this bit. Reserved The value read from this bit is indeterminate. Do not set this bit. Timer Overrun Interrupt Priority Level Most Significant bit POVRH POVRLPriority level 0 0 Lowest 0 1 1 0 1 1 Highest ADC Interrupt Priority Level Most Significant bit PADCH PADCL Priority level 0 0 Lowest 0 1 1 0 1 1 Highest Reserved The value read from this bit is indeterminate. Do not set this bit. 6 - 5 - 4 - 3 - 2 POVRH 1 PADCH 0 - Reset Value = XXXX X000b 96 AT89C5115 4128F-8051-05/06 AT89C5115 Electrical Characteristics Absolute Maximum Ratings* *NOTICE: I = industrial ....................................................... -40C to 85C Storage Temperature ................................... -65C to + 150C Voltage on VCC from VSS .....................................-0.5V to + 6V Voltage on Any Pin from V SS .....................-0.5V to VCC + 0.2V Power Dissipation ............................................................. 1 W Stresses at or above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions may affect device reliability. Power Dissipation value is based on the maximum allowable die temperature and the thermal resistance of the package. DC Parameters for Standard Voltage TA = -40C to +85C; VSS = 0 V; VCC = 3 volts to 5.5 volts; F = 0 to 40 MHz Table 72. DC Parameters in Standard Voltage Symbol VIL VIH VIH1(2) Parameter Input Low Voltage Input High Voltage except XTAL1, RST Input High Voltage, XTAL1, RST Min -0.5 0.2 VCC + 0.9 0.7 VCC Typ(1) Max 0.2Vcc - 0.1 VCC + 0.5 VCC + 0.5 0.3 VOL Output Low Voltage, ports 1, 2, 3 and 4(3) 0.45 1.0 VCC - 0.3 VOH Output High Voltage, ports 1, 2, 3, 4 and 5 VCC - 0.7 VCC - 1.5 RRST IIL ILI ITL CIO IPD RST Pulldown Resistor Logical 0 Input Current ports 1, 2, 3 and 4 Input Leakage Current Logical 1 to 0 Transition Current, ports 1, 2, 3 and 4 Capacitance of I/O Buffer Power-down Current 160 50 90 200 -50 10 -650 Unit V V V V V V V V V k A A A pF A Vin = 0.45V 0.45V < Vin < VCC Vin = 2.0V Fc = 1 MHz TA = 25C 3V < VCC < 5.5V(4) IOL = 100 A IOL = 1.6 mA IOL = 3.5 mA IOH = -10 A IOH = -30 A IOH = -60 A V CC = 5V 10% Test Conditions 10 400 ICCOP = 0.7 Freq (MHz) + 3 mA ICC Power Supply Current ICC_FLASH_WRITE(7) =0.4 Freq (MHz) + 20 mA ICCIDLE = 0.6 Freq (MHz) + 2 mA 3V < VCC < 5.5V(1)(2) Notes: 1. Typicals are based on a limited number of samples and are not guaranteed. The values listed are at room temperature. 2. Flash retention is guaranteed with the same formula for VCC min down to 0V. 97 4128F-8051-05/06 3. Under steady state (non-transient) conditions, IOL must be externally limited as follows: Maximum IOL per port pin: 10 mA Maximum IOL per 8-bit port: Ports 1, 2 and 3: 15 mA Maximum total IOL for all output pins: 71 mA If IOL exceeds the test condition, V OL may exceed the related specification. Pins are not guaranteed to sink current greater than the listed test conditions. 4. Power-down ICC is measured with all output pins disconnected; XTAL2 NC.; RST = VSS (See Figure 47.). 5. Idle ICC is measured with all output pins disconnected; XTAL1 driven with TCLCH , TCHCL = 5 ns, V IL = VSS + 0.5V, VIH = VCC 0.5V; XTAL2 N.C; RST = VSS (See Figure 46.). 6. Operating ICC is measured with all output pins disconnected; XTAL1 driven with TCLCH , TCHCL = 5 ns (See Figure 48.), V IL = VSS + 0.5V, VIH = V CC - 0.5V; XTAL2 N.C.; RST = VCC. ICC would be slightly higher if a crystal oscillator used (See Figure 45.). 7. ICC_FLASH_WRITE operating current while a Flash block write is on going. Figure 45. ICC Test Condition, Active Mode VCC ICC VCC VCC RST (NC) CLOCK SIGNAL XTAL2 XTAL1 VAGND VaVcc VSS All other pins are disconnected. Figure 46. ICC Test Condition, Idle Mode VCC ICC VCC VaVcc RST (NC) CLOCK SIGNAL XTAL2 XTAL1 VAGND VSS All other pins are disconnected. 98 AT89C5115 4128F-8051-05/06 AT89C5115 Figure 47. ICC Test Condition, Power-down Mode VCC ICC VCC VaVcc RST (NC) XTAL2 XTAL1 VAGND VSS All other pins are disconnected. Figure 48. Clock Signal Waveform for ICC Tests in Active and Idle Modes VCC-0.5V 0.45V TCLCH TCHCL TCLCH = TCHCL = 5ns. 0.7VCC 0.2VCC-0.1 DC Parameters for A/D Converter Table 73. DC Parameters for AD Converter in Precision Conversion Symbol Parameter AVin Analog input voltage Min Vss- 0.2 Typ(1) Max Unit Test Conditions V Max Vref + 0.6 Vcc 16 VaVcc Rref(2) Vref Rai Cai INL DNL OE Analog supply voltage Resistance between Vref and Vss Reference voltage Analog input Resistor Analog input Capacitance Integral non linearity Differential non linearity Offset error Vref 12 2.40 Vcc + 10% 24 3.00 400 V K V During sampling 60 1 0.5 -2 2 1 2 pF During sampling lsb lsb lsb Notes: 1. Typicals are based on a limited number of samples and are not guaranteed. 2. With ADC enabled. 99 4128F-8051-05/06 AC Parameters Serial Port Timing - Shift Register Mode Table 74. Symbol Description (F = 40 MHz) Symbol TXLXL TQVHX TXHQX TXHDX TXHDV Parameter Serial port clock cycle time Output data set-up to clock rising edge Output data hold after clock rising edge Input data hold after clock rising edge Clock rising edge to input data valid Table 75. AC Parameters for a Fix Clock (F = 40 MHz) Symbol TXLXL TQVHX TXHQX TXHDX TXHDV Min 300 200 30 0 117 Max Units ns ns ns ns ns Table 76. AC Parameters for a Variable Clock Symbol TXLXL TQVHX TXHQX TXHDX TXHDV Type Min Min Min Min Max Standard Clock 12 T 10 T - x 2T-x x 10 T - x X2 Clock 6T 5T-x T-x x 5 T- x 50 20 0 133 x parameter for -M range Units ns ns ns ns ns 100 AT89C5115 4128F-8051-05/06 AT89C5115 Shift Register Timing Waveforms INSTRUCTION 0 1 2 3 4 5 6 7 8 TXLXL CLOCK TQVXH OUTPUT DATA WRITE to SBUF INPUT DATA CLEAR RI 0 TXHDV VALID VALID TXHQX 1 2 TXHDX VALID VALID VALID VALID VALID 3 4 5 6 7 SET TI VALID SET RI External Clock Drive Characteristics (XTAL1) Table 77. AC Parameters Symbol TCLCL TCHCX TCLCX TCLCH TCHCL TCHCX/TCLCX Parameter Oscillator Period High Time Low Time Rise Time Fall Time Cyclic ratio in X2 Mode 40 Min 25 5 5 5 5 60 Max Units ns ns ns ns ns % External Clock Drive Waveforms VCC-0.5V 0.45V 0.7VCC 0.2VCC-0.1 TCHCL TCLCX TCLCL TCHCX TCLCH AC Testing Input/Output Waveforms VCC -0.5V INPUT/OUTPUT 0.45 V 0.2 VCC + 0.9 0.2 VCC - 0.1 AC inputs during testing are driven at VCC - 0.5 for a logic "1" and 0.45V for a logic "0". Timing measurement are made at VIH min for a logic "1" and VIL max for a logic "0". Float Waveforms FLOAT VOH - 0.1V VOL + 0.1V VLOAD VLOAD + 0.1V VLOAD - 0.1V 101 4128F-8051-05/06 For timing purposes as port pin is no longer floating when a 100 mV change from load voltage occurs and begins to float when a 100 mV change from the loaded VOH/V OL level occurs. IOL/IOH 20mA. Clock Waveforms Flash/EEPROM Memory Table 78. Memory AC Timing Vcc = 3.0V to 5.5V, TA = -40C to +85C Symbol TBHBL NFCY TFDR Parameter Flash/EEPROM Internal Busy (Programming) Time Number of Flash/EEPROM Erase/Write Cycles Flash/EEPROM Data Retention Time 100 000 10 Min Typ 13 Max 17 Unit ms Valid in normal clock mode. In X2 Mode XTAL2 must be changed to XTAL2/2. cycles years Figure 49. Flash Memory - Internal Busy Waveforms FBUSY bit TBHBL A/D Converter Table 79. AC Parameters for A/D Conversion Symbol TSETUP ADC Clock Frequency Parameter Min 4 700 Typ Max Unit s KHz 102 AT89C5115 4128F-8051-05/06 AT89C5115 Ordering Information Table 80. Possible Order Entries Part-Number T89C5115-SISIM T89C5115-TISIM T89C5115-RATIM AT89C5115-SISUM AT89C5115-TISUM AT89C5115-RATUM Memory Size 16K 16K 16K 16K 16K 16K Supply Voltage 5V 5V 5V 5V 5V 5V Temperature Range Industrial Industrial Industrial Industrial & Green Industrial & Green Industrial & Green Max Frequency 40 MHz 40 MHz 40 MHz 40 MHz 40 MHz 40 MHz Package PLCC28 SOIC28 VQFP32 PLCC28 SOIC28 VQFP32 Packing Stick Stick Tray Stick Stick Tray 103 4128F-8051-05/06 Package Drawings VQFP32 104 AT89C5115 4128F-8051-05/06 AT89C5115 PLCC28 105 4128F-8051-05/06 SOIC24 106 AT89C5115 4128F-8051-05/06 AT89C5115 SOIC28 107 4128F-8051-05/06 Datasheet Revision History for T89C5115 Changes from 4128A01/03 to 4128B-06/03 Changes from 4128B06/03 to 4128C-12/03 1. Changed the endurance of Flash to 100, 000 Write/Erase cycles. 2. Added note on Flash retention formula for VIH1, in Section "Electrical Characteristics", page 97. 1. Changed value of IPDMAX to 400, Section "Electrical Characteristics", page 97. 2. PCA , CPS0, register correction, Section "PCA Registers", page 78. 3. Cross Memory section added Section "Operation Cross Memory Access", page 42. Changes from 4128C 12/03 to 4128D - 01/05 Changes from 4128D 01/05 to 4128E - 10/05 Changes from 4128E 10/05 to 4182F - 06/05 1. Various minor corrections throughout the document. 1. Added green product ordering information. 1. Minor corrections throughout the document. 108 AT89C5115 4128F-8051-05/06 Table of Contents Features ................................................................................................. 1 Description ............................................................................................ 2 Block Diagram ....................................................................................... 2 Pin Configurations ................................................................................ 3 Pin Description...................................................................................... 5 I/O Configurations ................................................................................................. 7 Port Structure ....................................................................................................... 7 Read-Modify-Write Instructions ............................................................................ 8 Quasi Bi-directional Port Operation ...................................................................... 8 SFR Mapping ....................................................................................... 10 Clock .................................................................................................... 14 Description ......................................................................................................... 14 Register .............................................................................................................. 17 Power Management ............................................................................ 18 Reset Pin .............................................................................................. 18 At Power-up (cold reset)..................................................................................... 18 During a Normal Operation (Warm Reset) ......................................................... 19 Watchdog Reset................................................................................................. 19 Reset Recommendation to Prevent Flash Corruption ......................................... 20 Idle Mode............................................................................................................ 20 Power-down Mode ............................................................................................. 20 Registers ............................................................................................................. 23 Data Memory ....................................................................................... 24 Internal Space .................................................................................................... 24 Dual Data Pointer ............................................................................................... 26 Registers ............................................................................................................ 27 EEPROM Data Memory ....................................................................... 29 Write Data in the Column Latches...................................................................... Programming ...................................................................................................... Read Data .......................................................................................................... Examples............................................................................................................ Registers ............................................................................................................ 29 29 29 30 31 i Program/Code Memory ...................................................................... 32 Flash Memory Architecture ................................................................................ 32 Overview of FM0 Operations.............................................................................. 34 Registers ............................................................................................................ 40 Operation Cross Memory Access ..................................................... 42 Sharing Instructions ........................................................................... 43 In-System Programming (ISP) ........................................................... 45 Flash Programming and Erasure ....................................................................... Boot Process ...................................................................................................... Application-Programming-Interface .................................................................... XROW Bytes ...................................................................................................... Hardware Conditions .......................................................................................... Hardware Security Byte...................................................................................... 45 46 46 47 47 48 Serial I/O Port ...................................................................................... 49 Framing Error Detection .................................................................................... 49 Automatic Address Recognition ......................................................................... 50 Given Address .................................................................................................... 50 Broadcast Address ............................................................................................. 51 Registers ............................................................................................................. 52 Timers/Counters ................................................................................. 55 Timer/Counter Operations .................................................................................. Timer 0 ............................................................................................................... Timer 1 ............................................................................................................... Interrupt .............................................................................................................. Registers ............................................................................................................ 55 55 57 58 59 Timer 2 ................................................................................................. 62 Auto-Reload Mode ............................................................................................. 62 Programmable Clock-Output .............................................................................. 63 Registers ............................................................................................................ 64 Watchdog Timer .................................................................................. 67 Watchdog Programming...................................................................................... 68 Watchdog Timer During Power-down Mode and Idle ...................... 69 Register .............................................................................................................. 69 Programmable Counter Array (PCA) ................................................. 71 ii Table of Contents PCA Timer .......................................................................................................... PCA Modules ..................................................................................................... PCA Interrupt...................................................................................................... PCA Capture Mode ............................................................................................ 16-bit Software Timer Mode ............................................................................... High Speed Output Mode ................................................................................... Pulse Width Modulator Mode ............................................................................. PCA Registers .................................................................................................... 71 73 74 74 75 76 76 78 Analog-to-Digital Converter (ADC) .................................................... 83 Features ............................................................................................................. 83 ADC Port1 I/O Functions .................................................................................... 83 VAREF ............................................................................................................... 83 ADC Converter Operation .................................................................................. 84 Voltage Conversion ............................................................................................ 85 Clock Selection................................................................................................... 85 ADC Standby Mode............................................................................................ 85 IT ADC management.......................................................................................... 85 Routine Examples .............................................................................................. 86 Registers ............................................................................................................. 87 Interrupt System ................................................................................. 89 Introduction......................................................................................................... 89 Registers ............................................................................................................ 91 Electrical Characteristics ................................................................... 97 DC Parameters for Standard Voltage .......................................................................... 97 Absolute Maximum Ratings* .............................................................................. 97 DC Parameters for A/D Converter...................................................................... 99 AC Parameters ................................................................................................. 100 Ordering Information ........................................................................ 103 Package Drawings ............................................................................ 104 VQFP32............................................................................................................ PLCC28 ............................................................................................................ SOIC24............................................................................................................. SOIC28............................................................................................................. 104 105 106 107 Datasheet Revision History for T89C5115 ...................................... 108 Changes from 4128A-01/03 to 4128B-06/03.................................................... 108 Changes from 4128B-06/03 to 4128C-12/03 ................................................... 108 iii Changes from 4128C -12/03 to 4128D - 01/05................................................. 108 Changes from 4128D - 01/05 to 4128E - 10/05................................................ 108 Changes from 4128E - 10/05 to 4182F - 06/05 ................................................ 108 iv AT89C5115 4128F-8051-05/06 Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Atmel Operations Memory 2325 Orchard Parkway San Jose, CA 95131 Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 RF/Automotive Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany Tel: (49) 71-31-67-0 Fax: (49) 71-31-67-2340 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Regional Headquarters Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500 Microcontrollers 2325 Orchard Parkway San Jose, CA 95131 Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602 44306 Nantes Cedex 3, France Tel: (33) 2-40-18-18-18 Fax: (33) 2-40-18-19-60 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France Tel: (33) 4-76-58-30-00 Fax: (33) 4-76-58-34-80 Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel: (852) 2721-9778 Fax: (852) 2722-1369 ASIC/ASSP/Smart Cards Zone Industrielle 13106 Rousset Cedex, France Tel: (33) 4-42-53-60-00 Fax: (33) 4-42-53-60-01 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 literature@atmel.com Disclaimer: Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company's standard warranty which is detailed in Atmel's Terms and Conditions located on the Company's web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel's products are not authorized for use as critical components in life support devices or systems. (c) Atmel Corporation 2006. All rights reserved. Atmel(R), logo and combinations thereof, and Everywhere You Are (R) are the trademarks or registered trademarks, of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. Printed on recycled paper. 4128F-8051-05/06 /0M |
Price & Availability of AT89C5115-SISUM
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |